- 您现在的位置：买卖IC网 > PDF目录10674 > AD7682BCPZ (Analog Devices Inc)IC ADC 16BIT 4CH 250KSPS 20LFCSP PDF资料下载
参数资料
| 型号： | AD7682BCPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 24/32页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 4CH 250KSPS 20LFCSP |
| 产品培训模块： | Power Line Monitoring |
| 产品变化通告： | Startup Circuitry Design Improvement Change 15/April/2009 |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| 位数： | 16 |
| 采样率（每秒）： | 250k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 21mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 20-LFCSP-VQ |
| 包装： | 托盘 |
| 输入数目和类型： | 8 个单端，单极；4 个差分，双极；4 个伪差分，双极 |
| 产品目录页面： | 778 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页
AD7682/AD7689
Data Sheet
Rev. D | Page 30 of 32
READ/WRITE SPANNING CONVERSION WITH A
BUSY INDICATOR
any host using an SPI, serial port, or FPGA with an interrupt
input. The connection diagram is shown in Figure 42, and the
corresponding timing is given in Figure 43. For the SPI, the
host should use CPHA = CPOL = 1. Reading/writing spanning
conversion is shown, which covers all three modes detailed in
the Digital Interface section.
A rising edge on CNV initiates a conversion, ignores data
present on DIN and forces SDO to high impedance. After the
conversion is initiated, it continues until completion irrespec-
tive of the state of CNV. CNV must be returned low before the
safe data transfer time, tDATA, and then held low beyond the
conversion time, tCONV, to generate the busy signal indicator.
When the conversion is complete, SDO transitions from high
impedance to low (data ready), and with a pull-up to VIO, SDO
can be used to interrupt the host to begin data transfer.
the acquisition phase and power-down. The host must enable
the MSB of the CFG register at this time (if necessary) to begin
the CFG update. While CNV is low, both a CFG update and a
data readback take place. The first 14 SCK rising edges are used to
update the CFG register, and the first 16 SCK falling edges clock
out the conversion results starting with the MSB. The restric-
tion for both configuring and reading is that they both occur
before the tDATA time elapses for the next conversion. All 14 bits of
CFG[13:0] must be written or they are ignored. Also, if the 16-bit
conversion result is not read back before tDATA elapses, it is lost.
The SDO data is valid on both SCK edges. Although the rising
edge can be used to capture the data, a digital host using the
SCK falling edge allows a faster reading rate, provided it has an
acceptable hold time. After the optional 17th (or 31st) SCK
falling edge, SDO returns to high impedance. Note that if the
optional SCK falling edge is not used, the busy feature cannot
be detected, as described in the General Timing with a Busy
Indicator section.
If CFG readback is enabled, the CFG register associated with
the conversion result is read back MSB first following the LSB of
the conversion result. A total of 31 SCK falling edges is required
to return SDO to high impedance if this is enabled.
AD7682/
AD7689
MISO
MOSI
SCK
SS
SDO
VIO
FOR SPI USE CPHA = 1, CPOL = 1.
SCK
CNV
DIN
DIGITAL HOST
IRQ
07
35
3-
03
8
SCK
ACQUISITION (n)
ACQUISITION
(n + 1)
CNV
DIN
SDO
MSB
– 1
1
2
BEGIN DATA (n – 1)
BEIGN CFG (n + 1)
CFG
MSB
LSB
+ 1
LSB
15
SEE NOTE
NOTES:
1. THE LSB IS FOR CONVERSION RESULTS OR THE CONFIGURATION REGISTER CFG (n – 1) IF
16 SCK FALLING EDGES = LSB OF CONVERSION RESULTS.
30 SCK FALLING EDGES = LSB OF CONFIGURATION REGISTER.
ON THE 17TH OR 31st SCK FALLING EDGE, SDO IS DRIVEN TO HIGH IMPENDANCE.
OTHERWISE, THE LSB REMAINS ACTIVE UNTIL THE BUSY INDICATOR IS DRIVEN LOW.
16
17/
31
17/
31
CONVERSION (n)
CONVERSION
(n – 1)
(QUIET
TIME)
END DATA (n – 2)
END DATA (n – 1)
END CFG (n + 1)
END CFG (n)
X
XX
X
tDATA
UPDATE (n + 1)
CFG/SDO
LSB
+ 1
LSB
CONVERSION (n – 1)
(QUIET
TIME)
UPDATE (n)
CFG/SDO
tCYC
tACQ
tHDIN
tHSDO
tDSDO
tSDIN
tDATA
tCONV
tCNVH
tDIS
tEN
CFG
MSB –1
07
35
3-
03
9
tSCK
tSCKH
tSCKL
相关PDF资料 |
PDF描述 |
|---|---|
| AD7794BRUZ | IC ADC 24BIT SIG-DEL 6CH 24TSSOP |
| AD7689ACPZ | IC ADC 16BIT 250KSPS 8CH 20LFCSP |
| LTC1598CG#PBF | IC A/D CONV 12BIT SRL 8CH 24SSOP |
| KA339A | IC COMPARATOR QUAD 14-DIP |
| KA339 | IC COMPARATOR QUAD 14-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7682BCPZRL7 | 功能描述:IC ADC 16BIT 4CH 250KSPS 20LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7683 | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit, 100 kSPS PulSAR ADC in MSOP/QFN |
| AD7683ACPZRL | 功能描述:IC ADC 16BIT SRL 100KSPS 8LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7683ACPZRL7 | 功能描述:IC ADC 16BIT 100KSPS 8LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7683ARM | 制造商:Analog Devices 功能描述:ADC Single SAR 100ksps 16-bit Serial 8-Pin MSOP Tube |
发布紧急采购，3分钟左右您将得到回复。