- 您现在的位置：买卖IC网 > PDF目录10300 > AD7707BRZ-REEL (Analog Devices Inc)IC ADC 16BIT 3CHAN 20SOIC PDF资料下载
参数资料
| 型号： | AD7707BRZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/52页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 3CHAN 20SOIC |
| 标准包装： | 1,000 |
| 位数： | 16 |
| 采样率（每秒）： | 500 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 1mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC W |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个单端，单极；1 个单端，双极；2 个伪差分，单极；2 个伪差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
AD7707
Rev. B | Page 20 of 52
Setup Register (RS2, RS1, RS0 = 0, 0, 1); Power-On/Reset Status: 0x01
The setup register is an eight-bit register from which data can either be read or to which data can be written. Table 18 outlines the bit
designations for the setup register.
Table 18. Setup Register
MD1 (0)
MD0 (0)
G2 (0)
G1 (0)
G0 (0)
B/U (0)
BUF (0)
FSYNC (1)
Table 19.
Bit
Description
MD1, MD0
Operating mode selection bits.
G2 to G0
Gain selection bits. These bits select the gain setting for the on-chip PGA, as outlined in Table 21.
B/U
Bipolar/unipolar operation. A 0 in this bit selects Bipolar operation. A 1 in this bit selects unipolar operation.
BUF
Buffer control. With this bit at 0, the on-chip buffer on the analog input is shorted out. With the buffer shorted out, the
current flowing in the AVDD line is reduced. When this bit is high, the on-chip buffer is in series with the analog input
allowing the input to handle higher source impedances.
FSYNC
Filter synchronization. When this bit is high, the nodes of the digital filter, the filter control logic, and the calibration
control logic are held in a reset state, and the analog modulator is held in its reset state. When this bit goes low, the
modulator and filter start to process data and a valid word is available in 3 × 1/(output update rate), that is, the settling
time of the filter. This FSYNC bit does not affect the digital interface and does not reset the DRDY output if it is low.
Table 20. Operating Modes
MD1
MD0
Operating Mode
0
Normal mode: this is the normal mode of operation of the device whereby the device is performing normal conversions.
0
1
Self-calibration: this activates self-calibration on the channel selected by CH1 and CH0 of the communications register.
This is a one-step calibration sequence and, when complete, the part returns to normal mode with MD1 and MD0
returning to 0, 0. The DRDY output or bit goes high when calibration is initiated and returns low when this self-
calibration is complete and a new valid word is available in the data register. The zero-scale calibration is performed at
the selected gain on internally shorted (zeroed) inputs and the full-scale calibration is performed at the selected gain on
an internally-generated VREF/selected gain.
1
0
Zero-scale (ZS) system calibration: this activates zero-scale system calibration on the channel selected by CH1 and CH0
of the communications register. Calibration is performed at the selected gain on the input voltage provided at the
analog input during this calibration sequence. This input voltage should remain stable for the duration of the
calibration. The DRDY output or bit goes high when calibration is initiated and returns low when this zero-scale
calibration is complete and a new valid word is available in the data register. At the end of the calibration, the part
returns to ormal
ode with MD1 and MD0 returning to 0, 0.
1
Full-scale (FS) system calibration: this activates full-scale system calibration on the selected input channel. Calibration is
performed at the selected gain on the input voltage provided at the analog input during this calibration sequence. This
input voltage should remain stable for the duration of the calibration. The DRDY output or bit goes high when
calibration is initiated and returns low when this full-scale calibration is complete and a new valid word is available in
the data register. At the end of the calibration, the part returns to normal mode with MD1 and MD0 returning to 0, 0.
Table 21. Gain Selection
G2
G1
G0
Gain Setting
0
1
0
1
2
0
1
0
4
0
1
8
1
0
16
1
0
1
32
1
0
64
1
128
相关PDF资料 |
PDF描述 |
|---|---|
| MS27468T25B46B | CONN HSG RCPT 46POS JAMNUT SCKT |
| LTC2366CS6#TRPBF | IC ADC 12BIT 3MSPS TSOT23-6 |
| LTC1404IS8#PBF | IC A/D CONV 12BIT W/SHTDN 8-SOIC |
| MS27468E25B46B | CONN HSG RCPT 46POS JAMNUT SCKT |
| LTC1404IS8 | IC A/D CONV 12BIT W/SHTDN 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7707BRZ-REEL7 | 功能描述:IC ADC 16BIT 3CHAN 20SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7707EB | 制造商:AD 制造商全称:Analog Devices 功能描述:3 V/5 V 610 V Input Range 1 mW 3-Channel 16-Bit Sigma-Delta ADC(316.51 k) |
| AD7708 | 制造商:AD 制造商全称:Analog Devices 功能描述:8-/10-Channel, Low Voltage, Low Power, ADCs |
| AD7708BR | 功能描述:IC ADC 16BIT R-R 8/10CH 28-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
| AD7708BR-REEL | 功能描述:IC ADC 16BIT R-R 8/10CH 28-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率（每秒）:45k 数据接口:串行 转换器数目:2 功率耗散（最大）:315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端，单极 |
发布紧急采购，3分钟左右您将得到回复。