参数资料
型号: AD7707BRZ-REEL
厂商: Analog Devices Inc
文件页数: 17/52页
文件大小: 0K
描述: IC ADC 16BIT 3CHAN 20SOIC
标准包装: 1,000
位数: 16
采样率(每秒): 500
数据接口: DSP,MICROWIRE?,QSPI?,串行,SPI?
转换器数目: 1
功率耗散(最大): 1mW
电压电源: 模拟和数字
工作温度: -40°C ~ 85°C
安装类型: 表面贴装
封装/外壳: 20-SOIC(0.295",7.50mm 宽)
供应商设备封装: 20-SOIC W
包装: 带卷 (TR)
输入数目和类型: 1 个单端,单极;1 个单端,双极;2 个伪差分,单极;2 个伪差分,双极
AD7707
Rev. B | Page 24 of 52
CIRCUIT DESCRIPTION
The AD7707 is a Σ-Δ ADC with on-chip digital filtering, intended
for the measurement of wide dynamic range, low frequency
signals such as those in industrial control or process control
applications. It contains a Σ-Δ (or charge balancing) ADC, a
calibration microcontroller with on-chip static RAM, a clock
oscillator, a digital filter, and a bidirectional serial communica-
tions port. The part consumes only 320 μA of power supply
current, making it ideal for battery-powered or loop-powered
instruments. On-chip thin-film resistors allow ±10 V, ±5 V, 0 V
to 10 V, and 0 V to 5 V high level input signals to be directly
accommodated on the analog input without requiring split
supplies, dc-to-dc converters, or charge pumps. This part operates
with a supply voltage of 2.7 V to 3.3 V, or 4.75 V to 5.25 V.
The AD7707 contains two low level (AIN1 and AIN2) pro-
grammable-gain pseudo differential analog input channels and
one high level (AIN3) single-ended input channel. For the low
level input channels, the selectable gains are 1, 2, 4, 8, 16, 32, 64,
and 128, allowing the part to accept unipolar signals of between
0 mV to 20 mV and 0 V to 2.5 V, or bipolar signals in the range
from ±20 mV to ±2.5 V when the reference input voltage equals
2.5 V. With a reference voltage of 1.225 V, the input ranges are
from 0 mV to 10 mV to 0 V to 1.225 V in unipolar mode, and
from ±10 mV to ±1.225 V in bipolar mode. Note that the signals
are with respect to the LOCOM input.
The high level input channel can directly accept input signals
of ±10 V with respect to HICOM when operating with 5 V
supplies and a reference of 2.5 V. With 3 V supplies, ±5 V can
be accommodated on the AIN3 input.
The input signal to the analog input is continuously sampled at
a rate determined by the frequency of the master clock, MCLK
IN, and the selected gain. A charge-balancing ADC (Σ-Δ
modulator) converts the sampled signal into a digital pulse
train whose duty cycle contains the digital information. The
programmable gain function on the analog input is also
incorporated in this Σ-Δ modulator with the input sampling
frequency being modified to give the higher gains. A sinc3
digital low-pass filter processes the output of the Σ-Δ modulator
and updates the output register at a rate determined by the first
notch frequency of this filter. The output data can be read from
the serial port randomly or periodically at any rate up to the
output register update rate. The first notch of this digital filter
(and therefore its 3 dB frequency) can be programmed via the
clock register bits, FS0 to FS2. With a master clock frequency
of 2.4576 MHz, the programmable range for this first notch
frequency is from 10 Hz to 500 Hz, giving a programmable range
for the 3 dB frequency of 2.62 Hz to 131 Hz. With a master clock
frequency of 1 MHz, the programmable range for this first notch
frequency is from 4 Hz to 200 Hz, giving a programmable range for
the 3 dB frequency of 1.06 Hz to 52.4 Hz.
The basic connection diagram for the AD7707 is shown in
Figure 12. An AD780 or REF192 precision 2.5 V reference
provides the reference source for the part. On the digital side,
the part is configured for 3-wire operation with CS tied to
DGND. A quartz crystal or ceramic resonator provides the master
clock source for the part. In most cases, it is necessary to
connect capacitors on the crystal or resonator to ensure that it
does not oscillate at overtones of its fundamental operating
frequency. The values of capacitors can vary, depending on the
manufacturer’s specifications. A similar circuit is applicable for
operation with 3 V supplies; in this case, a 1.225 V reference
(AD1580) should be used for specified performance.
AVDD
DVDD
ANALOG
5V SUPPLY
10F
AIN1
AIN2
LOCOM
AIN3
VBIAS
HICOM
LOW LEVEL
ANALOG
INPUT
HIGH LEVEL
ANALOG
INPUT
AGND
DGND
REF IN(+)
REF IN(–)
10F
VIN
ANALOG 5V
SUPPLY
AD780/
REF192
VOUT
GND
AD7707
DRDY
DATA READY
DOUT
RECEIVE (READ)
DIN
SERIAL DATA
SCLK
SERIAL CLOCK
RESET
5V
CS
MCLK IN
MCLK OUT
CRYSTAL OR
CERAMIC
RESONATOR
0.1F
08
69
1-
0
1
2
Figure 12. Basic Connection Diagram for 5 V Operation
相关PDF资料
PDF描述
MS27468T25B46B CONN HSG RCPT 46POS JAMNUT SCKT
LTC2366CS6#TRPBF IC ADC 12BIT 3MSPS TSOT23-6
LTC1404IS8#PBF IC A/D CONV 12BIT W/SHTDN 8-SOIC
MS27468E25B46B CONN HSG RCPT 46POS JAMNUT SCKT
LTC1404IS8 IC A/D CONV 12BIT W/SHTDN 8-SOIC
相关代理商/技术参数
参数描述
AD7707BRZ-REEL7 功能描述:IC ADC 16BIT 3CHAN 20SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率(每秒):45k 数据接口:串行 转换器数目:2 功率耗散(最大):315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC(0.295",7.50mm 宽) 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端,单极
AD7707EB 制造商:AD 制造商全称:Analog Devices 功能描述:3 V/5 V 610 V Input Range 1 mW 3-Channel 16-Bit Sigma-Delta ADC(316.51 k)
AD7708 制造商:AD 制造商全称:Analog Devices 功能描述:8-/10-Channel, Low Voltage, Low Power, ADCs
AD7708BR 功能描述:IC ADC 16BIT R-R 8/10CH 28-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率(每秒):45k 数据接口:串行 转换器数目:2 功率耗散(最大):315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC(0.295",7.50mm 宽) 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端,单极
AD7708BR-REEL 功能描述:IC ADC 16BIT R-R 8/10CH 28-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:16 采样率(每秒):45k 数据接口:串行 转换器数目:2 功率耗散(最大):315mW 电压电源:模拟和数字 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:28-SOIC(0.295",7.50mm 宽) 供应商设备封装:28-SOIC W 包装:带卷 (TR) 输入数目和类型:2 个单端,单极