- 您现在的位置：买卖IC网 > PDF目录10239 > AD7714YRZ-REEL (Analog Devices Inc)IC ADC 24BIT SIGMA-DELTA 24SOIC PDF资料下载
参数资料
| 型号： | AD7714YRZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 7/40页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT SIGMA-DELTA 24SOIC |
| 标准包装： | 1,000 |
| 位数： | 24 |
| 采样率（每秒）： | 1k |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 7mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC W |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 3 个差分，单极；3 个差分，双极；5 个伪差分，单极；5 个伪差分，双极 |
| 配用： | EVAL-AD7714-3EBZ-ND - BOARD EVAL FOR AD7714 |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页
2
AD7714
REV. C
–15–
CH2
CH1
CH0
AIN(+)
AIN(–)
Type
Calibration Register Pair
0
AIN1
AIN6
Pseudo Differential
Register Pair 0
0
1
AIN2
AIN6
Pseudo Differential
Register Pair 1
0
1
0
AIN3
AIN6
Pseudo Differential
Register Pair 2
0
1
AIN4
AIN6
Pseudo Differential
Register Pair 2
1
0
AIN1
AIN2
Fully Differential
Register Pair 0
1
0
1
AIN3
AIN4
Fully Differential
Register Pair 1
1
0
AIN5
AIN6
Fully Differential
Register Pair 2
1
AIN6
Test Mode
Register Pair 2
Mode Register (RS2-RS0 = 0, 0, 1); Power On/Reset Status: 00 Hex
The Mode Register is an eight bit register from which data can either be read or to which data can be written. Table VIII outlines the
bit designations for the Mode Register.
Table VIII. Mode Register
MD2
MD1
MD0
G2
G1
G0
BO
FSYNC
MD2
MD1
MD0
Operating Mode
0
Normal Mode; this is the normal mode of operation of the device whereby the device is performing nor-
mal conversions. This is the default condition of these bits after Power-On or
RESET.
0
1
Self-Calibration; this activates self-calibration on the channel selected by CH2, CH1 and CH0 of the
Communications Register. This is a one step calibration sequence and when complete the part returns to
Normal Mode with MD2, MD1 and MD0 returning to 0, 0, 0. The
DRDY output or bit goes high when
calibration is initiated and returns low when this self-calibration is complete and a new valid word is
available in the data register. The zero-scale calibration is performed at the selected gain on internally
shorted (zeroed) inputs and the full-scale calibration is performed at the selected gain on an internally-
generated VREF/Selected Gain.
0
1
0
Zero-Scale System Calibration; this activates zero scale system calibration on the channel selected by
CH2, CH1 and CH0 of the Communications Register. Calibration is performed at the selected gain on
the input voltage provided at the analog input during this calibration sequence. This input voltage should
remain stable for the duration of the calibration. The
DRDY output or bit goes high when calibration is
initiated and returns low when this zero-scale calibration is complete and a new valid word is available in
the data register. At the end of the calibration, the part returns to Normal Mode with MD2, MD1 and
MD0 returning to 0, 0, 0.
0
1
Full-Scale System Calibration; this activates full-scale system calibration on the selected input channel.
Calibration is performed at the selected gain on the input voltage provided at the analog input during this
calibration sequence. This input voltage should remain stable for the duration of the calibration. Once
again, the
DRDY output or bit goes high when calibration is initiated and returns low when this full-scale
calibration is complete and a new valid word is available in the data register. At the end of the calibration,
the part returns to Normal Mode with MD2, MD1 and MD0 returning to 0, 0, 0.
Table VII. Channel Selection
CH2–CH0
Channel Select. These three bits select a channel either for conversion or for access to calibration coefficients as
outlined in Table VII. There are three pairs of calibration registers on the part. In fully differential mode, the part
has three input channels so each channel has its own pair of calibration registers. In pseudo-differential mode, the
AD7714 has five input channels with some of the input channel combinations sharing calibration registers. With
CH2, CH1 and CH0 at a logic 1, the part looks at the AIN6 input internally shorted to itself. This can be used as
a test method to evaluate the noise performance of the part with no external noise sources. In this mode, the AIN6
input should be connected to an external voltage within the allowable common-mode range for the part. The
Power-On or RESET status of these bits is 1,0,0 selecting the differential pair AIN1 and AIN2.
相关PDF资料 |
PDF描述 |
|---|---|
| VI-23B-CU-F3 | CONVERTER MOD DC/DC 95V 200W |
| VI-B7Z-MW | CONVERTER MOD DC/DC 2V 40W |
| VE-B2V-MW-F3 | CONVERTER MOD DC/DC 5.8V 100W |
| VI-23B-CU-F2 | CONVERTER MOD DC/DC 95V 200W |
| VI-234-IW-S | CONVERTER MOD DC/DC 48V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7714YRZ-REEL7 | 功能描述:IC ADC 24BIT SIGMA-DELTA 24SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7715 | 制造商:AD 制造商全称:Analog Devices 功能描述:3 V/5 V, 450 uA 16-Bit, Sigma-Delta ADC |
| AD7715_10 | 制造商:AD 制造商全称:Analog Devices 功能描述:3 V/5 V, 450 ??A 16-Bit, Sigma-Delta ADC |
| AD7715-5EB | 制造商:Analog Devices 功能描述: |
发布紧急采购，3分钟左右您将得到回复。