- 您现在的位置：买卖IC网 > PDF目录10160 > AD7763BSVZ-REEL (Analog Devices Inc)IC ADC 24BIT S/D 625KSPS 64-TQFP PDF资料下载
参数资料
| 型号： | AD7763BSVZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 17/33页 |
| 文件大小： | 0K |
| 描述： | IC ADC 24BIT S/D 625KSPS 64-TQFP |
| 标准包装： | 1,500 |
| 位数： | 24 |
| 采样率（每秒）： | 625k |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 955.5mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-TQFP 裸露焊盘 |
| 供应商设备封装： | 64-TQFP-EP（10x10） |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 1 个差分，单极；1 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页当前第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页
Data Sheet
AD7763
Rev. B | Page 23 of 32
SUPPLY DECOUPLING
Every supply pin must be connected to the appropriate supply
via a ferrite bead and decoupled to the correct ground pin with
a 100 nF, 0603 case size, X7R dielectric capacitor. There are two
exceptions
Pin 12 (AV
DD4
) must have a 10 Ω resistor inserted between
the pin and a 10 nF decoupling capacitor.
Pin 27 (AV
DD2
) does not require a separate decoupling
capacitor or a direct connection to the supply; instead,
it is connected to Pin 14 via an 8.2 nH inductor.
The ferrite beads that are used to connect each supply pin to the
appropriate power supply should have a characteristic impedance
of 600 Ω to 1 MΩ at frequencies around 100 MHz, a dc impedance
of 1 Ω or less, and a rated current of 200 mA.
ADDITIONAL DECOUPLING
There are two other decoupling pins on the AD7763: Pin 8
(DECAPA) and Pin 30 (DECAPB). Pin 8 should be decoupled
with a 100 nF capacitor, and Pin 30 requires a 33 pF capacitor.
REFERENCE VOLTAGE FILTERING
A low noise reference source, such as the ADR431 (2.5 V) or
ADR434 (4.096 V), is suitable for use with the AD7763. The
reference voltage supplied to the AD7763 should be decoupled
and filtered, as shown in Figure 36.
The recommended scheme for the reference voltage supply
is a 100 Ω series resistor connected to a 100 μF tantalum
capacitor, followed by a series resistor of 10 Ω, and finally, a
10 nF decoupling capacitor very close to the VREF pin.
054
76-
02
1
12V
PIN 10
VOUT
2
+VIN
6
4
C15
10
F
C9
100nF
C10
100nF
R30
100
R17
10
+
C46
10nF
C11
100
F
+
ADR434
GND
U3
Figure 36. Reference Connection
DIFFERENTIAL AMPLIFIER COMPONENTS
The correct components for use around the on-chip differential
amplifier are shown in Table 10. Matching the components on
both sides of the differential amplifier is important to minimize
distortion of the signal applied to the amplifier. A tolerance of
0.1% or better is required for these components. Symmetrical
routing of the tracks on both sides of the differential amplifier
also assists in achieving stated performance.
EXPOSED PADDLE
The AD7763 64-lead TQFP_EP employs a 6 mm × 6 mm exposed
paddle (see Figure 39). The paddle reduces the thermal resistance
of the package by providing a path of low thermal resistance to
the PCB and, in turn, increases the heat transfer efficiency from
the AD7763 package. Soldering the exposed paddle to the AGND
plane of the PCB is fundamental in creating the conditions that
allow the AD7763 package to perform to the highest specifications
possible.
LAYOUT CONSIDERATIONS
While using the correct components is essential to achieve
optimum performance, the correct layout is just as important.
The Design Tools section of the AD7763 product page on
the Analog Devices website contains the Gerber files for the
AD7763 evaluation board. These files should be used as a
reference when designing any system using the AD7763.
The location and orientation of some of the components
mentioned in previous sections are critical, and particular
attention must be paid to the components that are located close
to the AD7763. Locating these components farther away from
the devices can have a direct impact on the maximum
performance achievable.
The use of ground planes should also be carefully considered.
To ensure that the return currents through the decoupling
capacitors are flowing to the correct ground pin, the ground
side of the capacitors should be as close as possible to the ground
pin associated with that supply. A ground plane should not be
relied upon as the sole return path for decoupling capacitors,
because the return current path using ground planes is not
easily predicted.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27468T11F4SC | CONN RCPT 4POS JAM NUT W/SCKT |
| MS3106R28-12SX | CONN PLUG 26POS STRAIGHT W/SCKT |
| 23282-31SG-350 | CONN PLUG 31POS CABLE SKT |
| VI-B3J-MW-F4 | CONVERTER MOD DC/DC 36V 100W |
| MS3106R28-12S | CONN PLUG 26POS STRAIGHT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7764 | 制造商:AD 制造商全称:Analog Devices 功能描述:24-Bit, 8.5 mW, 109 dB, 128/64/32 kSPS ADCs |
| AD7764_07 | 制造商:AD 制造商全称:Analog Devices 功能描述:24-Bit, 312 kSPS, 109 dB ヒ-ツ ADC with On-Chip Buffers and Serial Interface |
| AD7764BRUZ | 功能描述:IC ADC 24BIT S/D 312KSPS 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7764BRUZ-REEL7 | 功能描述:IC ADC 24BIT S/D 312KSPS 28TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7765 | 制造商:AD 制造商全称:Analog Devices 功能描述:24-Bit, 8.5 mW, 109 dB, 128/64/32 kSPS ADCs |
发布紧急采购，3分钟左右您将得到回复。