- 您现在的位置：买卖IC网 > PDF目录10307 > AD7795BRUZ-REEL (Analog Devices Inc)IC ADC 16BIT 6CH LOW-PWR 24TSSOP PDF资料下载
参数资料
| 型号： | AD7795BRUZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/37页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 6CH LOW-PWR 24TSSOP |
| 标准包装： | 2,500 |
| 位数： | 16 |
| 采样率（每秒）： | 470 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 2.5mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 6 个差分，单极；6 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
AD7794/AD7795
Rev. D | Page 17 of 36
ON-CHIP REGISTERS
The ADC is controlled and configured via a number of on-chip
registers that are described in the following sections. In the
following descriptions, set implies a Logic 1 state and cleared
implies a Logic 0 state, unless otherwise noted.
COMMUNICATIONS REGISTER
RS2, RS1, RS0 = 0, 0, 0
The communications register is an 8-bit write-only register. All
communications to the part must start with a write operation to
the communications register. The data written to the communi-
cations register determines whether the next operation is a read
or write operation, and to which register this operation takes
place. For read or write operations, once the subsequent read or
write operation to the selected register is complete, the interface
returns to where it expects a write operation to the
communications register. This is the default state of the
interface and, on power-up or after a reset, the ADC is in this
default state waiting for a write operation to the communications
register. In situations where the interface sequence is lost, a
write operation of at least 32 serial clock cycles with DIN high
returns the ADC to this default state by resetting the entire part.
Table 14 outlines the bit designations for the communications
register. CR0 through CR7 indicate the bit location, with CR
denoting the bits are in the communications register. CR7
denotes the first bit of the data stream. The number in brackets
indicates the power-on/reset default status of that bit.
CR7
CR6
CR5
CR4
CR3
CR2
CR1
CR0
WEN(0)
R/W(0)
RS2(0)
RS1(0)
RS0(0)
CREAD(0)
0(0)
Table 14. Communications Register Bit Designations
Bit No.
Mnemonic
Description
CR7
WEN
Write Enable Bit. A 0 must be written to this bit so that the write to the communications register actually occurs. If
a 1 is the first bit written, the part does not clock on to subsequent bits in the register. It stays at this bit location
until a 0 is written to this bit. Once a 0 is written to the WEN bit, the next seven bits are loaded to the
communications register.
CR6
R/W
A 0 in this bit location indicates that the next operation is a write to a specified register. A 1 in this position
indicates that the next operation is a read from the designated register.
CR5 to
CR3
RS2 to RS0
Register Address Bits. These address bits are used to select which registers of the ADC are being selected during
this serial interface communication. See Table 15.
CR2
CREAD
Continuous Read of the Data Register. When this bit is set to 1 (and the data register is selected), the serial
interface is configured so that the data register can be read continuously, that is, the contents of the data register
are automatically placed on the DOUT pin when the SCLK pulses are applied after the RDY pin goes low to
indicate that a conversion is complete. The communications register does not have to be written to for data reads.
To enable continuous read mode, the instruction 01011100 must be written to the communications register. To
exit the continuous read mode, the instruction 01011000 must be written to the communications register while
the RDY pin is low. While in continuous read mode, the ADC monitors activity on the DIN line so it can receive the
instruction to exit continuous read mode. Additionally, a reset occurs if 32 consecutive 1s are seen on DIN.
Therefore, DIN should be held low in continuous read mode until an instruction is written to the device.
CR1 to
CR0
0
These bits must be programmed to Logic 0 for correct operation.
Table 15. Register Selection
RS2
RS1
RS0
Register
Register Size
0
Communications Register During a Write Operation
8-bit
0
Status Register During a Read Operation
8-bit
0
1
Mode Register
16-bit
0
1
0
Configuration Register
16-bit
0
1
Data Register
24-bit (AD7794)/16-Bit (AD7795)
1
0
ID Register
8-bit
1
0
1
IO Register
8-bit
1
0
Offset Register
24-bit (AD7794)/16-Bit (AD7795)
1
Full-Scale Register
24-bit (AD7794)/16-Bit (AD7795)
相关PDF资料 |
PDF描述 |
|---|---|
| 14292-20PG-300 | CONN RCPT 20POS PNL MNT PIN |
| MS27466T15F5SC | CONN RCPT 5POS WALL MT W/SCKT |
| CXC3102A14S2S | CONN RCPT 4POS PNL MNT SKT |
| VE-BNX-IW-B1 | CONVERTER MOD DC/DC 5.2V 100W |
| AD9281ARSRL | IC ADC 8BIT DUAL CMOS 28-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7795BRUZ-REEL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:6-Channel, Low Noise, Low Power, 24-/16-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
| AD7796 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, 16-/24-Bit Sigma-Delta ADC for Bridge Sensors |
| AD7796BRUZ | 功能描述:IC ADC 16BIT SIG-DEL 1CH 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7796BRUZ-REEL | 功能描述:IC ADC 16BIT SIG-DEL 1CH 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7797 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, 16-/24-Bit Sigma-Delta ADC for Bridge Sensors |
发布紧急采购，3分钟左右您将得到回复。