- 您现在的位置：买卖IC网 > PDF目录10307 > AD7795BRUZ-REEL (Analog Devices Inc)IC ADC 16BIT 6CH LOW-PWR 24TSSOP PDF资料下载
参数资料
| 型号： | AD7795BRUZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 29/37页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 6CH LOW-PWR 24TSSOP |
| 标准包装： | 2,500 |
| 位数： | 16 |
| 采样率（每秒）： | 470 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 2.5mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 6 个差分，单极；6 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页当前第29页第30页第31页第32页第33页第34页第35页第36页第37页
AD7794/AD7795
Rev. D | Page 34 of 36
one conversion cycle when chop is disabled. For higher gains,
four conversion cycles are required to perform the full-scale
calibration when chop is enabled, and two conversion cycles
when chop is disabled. DOUT/RDY goes high when the
calibration is initiated and returns low when the calibration is
complete. The ADC is placed in idle mode following a cali-
bration. The measured full-scale coefficient is placed in the full-
scale register of the selected channel. Internal full-scale
calibrations cannot be performed when the gain equals 128.
With this gain setting, a system full-scale calibration can be
performed. A full-scale calibration is required each time the
gain of a channel is changed to minimize the full-scale error.
An internal full-scale calibration can be performed at specified
update rates only. For gains of 1, 2, and 4, an internal full-scale
calibration can be performed at any update rate. However, for
higher gains, internal full-scale calibrations can be performed
only when the update rate is less than or equal to 16.7 Hz, 33.3 Hz,
and 50 Hz. However, the full-scale error does not vary with
update rate, so a calibration at one update is valid for all update
rates (assuming the gain or reference source is not changed).
A system full-scale calibration takes two conversion cycles to
complete, irrespective of the gain setting when chop is enabled
and one conversion cycle when chop is disabled. A system full-
scale calibration can be performed at all gains and all update
rates. With chop disabled, the offset calibration (internal or
system offset) should be performed before the system full-scale
calibration is initiated.
GROUNDING AND LAYOUT
Because the analog inputs and reference inputs of the ADC are
differential, most of the voltages in the analog modulator are
common-mode voltages. The excellent common-mode
rejection of the part removes common-mode noise on these
inputs. The digital filter provides rejection of broadband noise
on the power supply, except at integer multiples of the
modulator sampling frequency. The digital filter also removes
noise from the analog and reference inputs, provided that these
noise sources do not saturate the analog modulator. As a result,
the AD7794/AD7795 are more immune to noise interference
than conventional high resolution converters. However, because
the resolution of the AD7794/AD7795 is so high, and the noise
levels from the AD7794/AD7795 are so low, care must be taken
with regard to grounding and layout.
The printed circuit board that houses the AD7794/AD7795
should be designed so that the analog and digital sections are
separated and confined to certain areas of the board. A minimum
etch technique is generally best for ground planes because it
gives the best shielding.
It is recommended that the GND pin of the AD7794/AD7795
be tied to the AGND plane of the system. In any layout, it is
important that the user keep in mind the flow of currents in the
system, ensuring that the return paths for all currents are as
close as possible to the paths the currents took to reach their
destinations. Avoid forcing digital currents to flow through the
AGND sections of the layout.
The ground plane of the AD7794/AD7795 should be allowed to
run under the AD7794/AD7795 to prevent noise coupling. The
power supply lines to the AD7794/AD7795 should use as wide a
trace as possible to provide low impedance paths and reduce the
effects of glitches on the power supply line. Fast switching
signals, such as clocks, should be shielded with digital ground
to avoid radiating noise to other sections of the board. In
addition, clock signals should never be run near the analog
inputs. Avoid crossover of digital and analog signals. Traces on
opposite sides of the board should run at right angles to each
other. This reduces the effects of feedthrough through the
board. A microstrip technique is the best, but it is not always
possible with a double-sided board. In this technique, the
component side of the board is dedicated to ground planes,
while signals are placed on the solder side.
Good decoupling is important when using high resolution
ADCs. AVDD should be decoupled with 10 μF tantalum in
parallel with 0.1 μF capacitors to GND. DVDD should be
decoupled with 10 μF tantalum in parallel with 0.1 μF
capacitors to the system’s DGND plane, with the system’s
AGND to DGND connection being close to the
AD7794/AD7795. To achieve the best from these decoupling
components, they should be placed as close as possible to the
device, ideally right up against the device. All logic chips should
be decoupled with 0.1 μF ceramic capacitors to DGND.
相关PDF资料 |
PDF描述 |
|---|---|
| 14292-20PG-300 | CONN RCPT 20POS PNL MNT PIN |
| MS27466T15F5SC | CONN RCPT 5POS WALL MT W/SCKT |
| CXC3102A14S2S | CONN RCPT 4POS PNL MNT SKT |
| VE-BNX-IW-B1 | CONVERTER MOD DC/DC 5.2V 100W |
| AD9281ARSRL | IC ADC 8BIT DUAL CMOS 28-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7795BRUZ-REEL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:6-Channel, Low Noise, Low Power, 24-/16-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
| AD7796 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, 16-/24-Bit Sigma-Delta ADC for Bridge Sensors |
| AD7796BRUZ | 功能描述:IC ADC 16BIT SIG-DEL 1CH 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7796BRUZ-REEL | 功能描述:IC ADC 16BIT SIG-DEL 1CH 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7797 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, 16-/24-Bit Sigma-Delta ADC for Bridge Sensors |
发布紧急采购，3分钟左右您将得到回复。