- 您现在的位置：买卖IC网 > PDF目录10307 > AD7795BRUZ-REEL (Analog Devices Inc)IC ADC 16BIT 6CH LOW-PWR 24TSSOP PDF资料下载
参数资料
| 型号： | AD7795BRUZ-REEL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 25/37页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 6CH LOW-PWR 24TSSOP |
| 标准包装： | 2,500 |
| 位数： | 16 |
| 采样率（每秒）： | 470 |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 2.5mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 105°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-TSSOP（0.173"，4.40mm 宽） |
| 供应商设备封装： | 24-TSSOP |
| 包装： | 带卷 (TR) |
| 输入数目和类型： | 6 个差分，单极；6 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页当前第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页
AD7794/AD7795
Rev. D | Page 30 of 36
Single Conversion Mode
In single conversion mode, the AD7794/AD7795 are placed in
shutdown mode between conversions. When a single
conversion is initiated by setting MD2 to 0, MD1 to 0, and MD0
to 1 in the mode register, the AD7794/AD7795 power up,
perform a single conversion, and then return to shutdown
mode. The on-chip oscillator requires 1 ms to power up. A
conversion requires a time period of 2 × tADC. DOUT/RDY goes
low to indicate the completion of a conversion. When the data-
word has been read from the data register, DOUT/RDY goes
high. If CS is low, DOUT/RDY remains high until another
conversion is initiated and completed. The data register can be
read several times, if required, even when DOUT/RDY has
gone high.
Continuous Conversion Mode
This is the default power-up mode. The AD7794/AD7795
continuously convert with the RDY pin in the status register
going low each time a conversion is complete. If CS is low, the
DOUT/RDY line also goes low when a conversion is complete.
To read a conversion, the user writes to the communications
register, indicating that the next operation is a read of the data
register. The digital conversion is placed on the DOUT/RDY
pin as soon as SCLK pulses are applied to the ADC. DOUT/RDY
returns high when the conversion is read. The user can read this
register additional times, if required. However, the user must
ensure that the data register is not being accessed at the completion
of the next conversion, or else the new conversion word is lost.
Continuous Read
Rather than write to the communications register each time a
conversion is complete to access the data, the AD7794/AD7795
can be configured so that the conversions are placed on the
DOUT/RDY line automatically. By writing 01011100 to the
communications register, the user need only apply the
appropriate number of SCLK cycles to the ADC. The 24-bit
word is automatically placed on the DOUT/RDY line when a
conversion is complete. The ADC should be configured for
continuous conversion mode.
When DOUT/RDY goes low to indicate the end of a conversion,
sufficient SCLK cycles must be applied to the ADC, and the
data conversion is placed on the DOUT/RDY line. When the
conversion is read, DOUT/RDY returns high until the next
conversion is available.
In this mode, the data can be read only once. Also, the user must
ensure that the data-word is read before the next conversion is
complete. If the user has not read the conversion before the
completion of the next conversion, or if insufficient serial clocks are
applied to the AD7794/AD7795 to read the word, the serial
output register is reset when the next conversion is complete.
The new conversion is then placed in the output serial register.
To exit the continuous read mode, the instruction 01011000
must be written to the communications register while the RDY
pin is low. While in the continuous read mode, the ADC
monitors activity on the DIN line so that it can receive the
instruction to exit the continuous read mode. Additionally, a
reset occurs if 32 consecutive 1s are seen on DIN. Therefore,
DIN should be held low in continuous read mode until an
instruction is to be written to the device.
相关PDF资料 |
PDF描述 |
|---|---|
| 14292-20PG-300 | CONN RCPT 20POS PNL MNT PIN |
| MS27466T15F5SC | CONN RCPT 5POS WALL MT W/SCKT |
| CXC3102A14S2S | CONN RCPT 4POS PNL MNT SKT |
| VE-BNX-IW-B1 | CONVERTER MOD DC/DC 5.2V 100W |
| AD9281ARSRL | IC ADC 8BIT DUAL CMOS 28-SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7795BRUZ-REEL1 | 制造商:AD 制造商全称:Analog Devices 功能描述:6-Channel, Low Noise, Low Power, 24-/16-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
| AD7796 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, 16-/24-Bit Sigma-Delta ADC for Bridge Sensors |
| AD7796BRUZ | 功能描述:IC ADC 16BIT SIG-DEL 1CH 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7796BRUZ-REEL | 功能描述:IC ADC 16BIT SIG-DEL 1CH 16TSSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:2,500 系列:- 位数:16 采样率（每秒）:15 数据接口:MICROWIRE?，串行，SPI? 转换器数目:1 功率耗散（最大）:480µW 电压电源:单电源 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:38-WFQFN 裸露焊盘 供应商设备封装:38-QFN（5x7） 包装:带卷 (TR) 输入数目和类型:16 个单端，双极；8 个差分，双极 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| AD7797 | 制造商:AD 制造商全称:Analog Devices 功能描述:Low Power, 16-/24-Bit Sigma-Delta ADC for Bridge Sensors |
发布紧急采购，3分钟左右您将得到回复。