参数资料
型号: AD7872ANZ
厂商: Analog Devices Inc
文件页数: 3/16页
文件大小: 0K
描述: IC ADC 14BIT SAMPLING 16DIP
标准包装: 1
位数: 14
采样率(每秒): 83k
数据接口: 串行
转换器数目: 1
功率耗散(最大): 95mW
电压电源: 双 ±
工作温度: -40°C ~ 85°C
安装类型: 通孔
封装/外壳: 16-DIP(0.300",7.62mm)
供应商设备封装: 16-PDIP
包装: 管件
输入数目和类型: 1 个单端,双极
AD7871/AD7872
–11–
REV. D
microprocessor and the conversion result is read from the ADC
with the following instruction:
ADSP-2100 MR0 = DM(ADC)
TMS32020/C25: IN D,ADC
MR0 = ADSP-2100 MR0 Register
D = Data Memory Address
ADC = AD7871 Address
Figure 17. AD7871 to ADSP-2100 Parallel Interface
Figure 18. AD7871 to TMS32020/C25 Interface
Some applications may require that conversions be initiated by
the microprocessor rather than an external timer. One option is
to decode the AD7871
CONVST from the address bus so that a
write operation to the ADC starts a conversion. Data is read at
the end of conversion as described earlier. Note, a read opera-
tion must not be attempted during conversion.
Using the CCIF standard where two input frequencies near the
top end of the input bandwidth are used, the second and third or-
der terms are of different significance. The second order terms
are usually distanced in frequency from the original sine waves
while the third order terms are usually at a frequency close to the
input frequencies. As a result, the second and third order terms
are specified separately. The calculation of the intermodulation
distortion is as per the THD specification where it is the ratio of
the rms sum of the individual distortion products to the rms
amplitude of the fundamental expressed in dBs. In this case, the
input consists of two, equal amplitude, low distortion sine waves.
Figure 16 shows a typical IMD plot for the AD7871/AD7872.
Figure 16. IMD Plot
Peak Harmonic or Spurious Noise
Peak Harmonic or Spurious Noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fs/2 and excluding dc) to the rms value of the
fundamental. Normally, the value of this specification will be
determined by the largest harmonic in the spectrum, but for
parts where the harmonics are buried in the noise floor, peak
will be a noise peak.
MICROPROCESSOR INTERFACE
The AD7871 and AD7872 have a wide variety of interfacing op-
tions. The AD7871 offers two operating modes and three
data-output formats, while the AD7872 is a dedicated serial
output device. The fast data access times on the parallel modes
of the AD7871 allow interfacing to the very fast DSPs. The se-
rial mode on both the AD7871 and AD7872 is compatible with
the serial port structures on all the popular DSPs.
Parallel Read Interfacing
Figures 17 and 18 show interfaces to the ADSP-2100 and the
TMS32020/C25 DSP processors. The AD7871 is operating in
Mode 1, parallel read for both interfaces. An external timer con-
trols conversion start asynchronously to the microprocessor. At
the end of each conversion the ADC
BUSY/INT interrupts the
相关PDF资料
PDF描述
AD676KNZ IC ADC 16BIT 100KSPS 28-DIP
MS3106E28-21PW CONN PLUG 37POS STRAIGHT W/PINS
MS3106E20-29SZ CONN PLUG 17POS STRAIGHT W/SCKT
MS27473T10C99S CONN PLUG 7POS STRAIGHT W/SCKT
IDT72V801L20PF IC SYNC FIFO 256X9 20NS 64QFP
相关代理商/技术参数
参数描述
AD7872AQ 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog-to-Digital Converter, 14-Bit
AD7872BQ 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog-to-Digital Converter, 14-Bit
AD7872BR 功能描述:IC ADC 14BIT SAMPLING 16-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率(每秒):83k 数据接口:串行,并联 转换器数目:1 功率耗散(最大):95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP(0.600",15.24mm) 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端,双极
AD7872BR-REEL 功能描述:IC ADC 14BIT SAMPLING 16-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率(每秒):83k 数据接口:串行,并联 转换器数目:1 功率耗散(最大):95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP(0.600",15.24mm) 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端,双极
AD7872BRZ 功能描述:IC ADC 14BIT SAMPLING 16SOIC RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率(每秒):83k 数据接口:串行,并联 转换器数目:1 功率耗散(最大):95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP(0.600",15.24mm) 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端,双极