- 您现在的位置：买卖IC网 > PDF目录10664 > AD7980BCPZ-RL7 (Analog Devices Inc)IC ADC 16BIT 1MSPS SAR 10LFCSP PDF资料下载
参数资料
| 型号： | AD7980BCPZ-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 1MSPS SAR 10LFCSP |
| 标准包装： | 1 |
| 系列： | PulSAR® |
| 位数： | 16 |
| 采样率（每秒）： | 1M |
| 数据接口： | DSP，MICROWIRE?，QSPI?，串行，SPI? |
| 转换器数目： | 1 |
| 功率耗散（最大）： | 9mW |
| 电压电源： | 单电源 |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-WFDFN 裸露焊盘，CSP |
| 供应商设备封装： | 10-LFCSP-WD（3x3） |
| 包装： | 标准包装 |
| 输入数目和类型： | 1 个伪差分，单极 |
| 其它名称： | AD7980BCPZ-RL7DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
Data Sheet
AD7980
Rev. C | Page 23 of 28
APPLICATION HINTS
LAYOUT
The printed circuit board (PCB) that houses the AD7980
should be designed so that the analog and digital sections are
separated and confined to certain areas of the board. The pinout of
the AD7980, with all its analog signals on the left side and all its
digital signals on the right side, eases this task.
Avoid running digital lines under the device because these couple
noise onto the die, unless a ground plane under the AD7980 is
used as a shield. Fast switching signals, such as CNV or clocks,
should never run near analog signal paths. Crossover of digital
and analog signals should be avoided.
At least one ground plane should be used. It can be common or
split between the digital and analog section. In the latter case,
the planes should be joined underneath the AD7980s.
The AD7980 voltage reference input REF has a dynamic input
impedance and should be decoupled with minimal parasitic
inductances. This is done by placing the reference decoupling
ceramic capacitor close to, ideally right up against, the REF and
GND pins and connecting them with wide, low impedance traces.
Finally, the power supplies VDD and VIO of the AD7980
should be decoupled with ceramic capacitors, typically 100 nF,
placed close to the AD7980 and connected using short and wide
traces to provide low impedance paths and reduce the effect of
glitches on the power supply lines.
An example of a layout following these rules is shown in
EVALUATING THE PERFORMANCE OF THE AD7980
Other recommended layouts for the AD7980 are outlined
in the documentation of the evaluation board for the AD7980
(EVAL-AD7980SDZ). The evaluation board package includes
a fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the
EVAL-SDP-CB1Z.
06392-
028
AD7980
Figure 43. Example Layout of the AD7980 (Top Layer)
06392-
027
Figure 44. Example Layout of the AD7980 (Bottom Layer)
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J1N-MW-F4 | CONVERTER MOD DC/DC 18.5V 100W |
| MAX9646EBS+TG45 | IC COMPARATOR W/REF 4UCSP |
| MAX3086CSD+T | IC TXRX RS485/422 10MBPS 14-SOIC |
| MAX9645EUK+T | IC COMPARATOR W/REF SOT23-5 |
| VE-J1N-MW-F2 | CONVERTER MOD DC/DC 18.5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD7980BRMZ | 功能描述:ADC 16BIT 1MSPS 1.25LSB 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1 系列:microPOWER™ 位数:8 采样率（每秒）:1M 数据接口:串行，SPI? 转换器数目:1 功率耗散（最大）:- 电压电源:模拟和数字 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:24-VFQFN 裸露焊盘 供应商设备封装:24-VQFN 裸露焊盘（4x4） 包装:Digi-Reel® 输入数目和类型:8 个单端，单极 产品目录页面:892 (CN2011-ZH PDF) 其它名称:296-25851-6 |
| AD7980BRMZRL7 | 功能描述:ADC 16BIT 1MSPS LP 10-MSOP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:PulSAR® 标准包装:1,000 系列:- 位数:12 采样率（每秒）:300k 数据接口:并联 转换器数目:1 功率耗散（最大）:75mW 电压电源:单电源 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC 包装:带卷 (TR) 输入数目和类型:1 个单端，单极；1 个单端，双极 |
| AD7980-EP | 制造商:AD 制造商全称:Analog Devices 功能描述:16-Bit, 1 MSPS PulSAR ADC in MSOP QFN |
| AD7980SRMZ-EP | 制造商:Analog Devices 功能描述:16-BIT, 1 MSPS PULSAR ADC IN MSOP/QFN - Rail/Tube |
| AD7980SRMZ-EP-RL7 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:ADC 16BIT 1MSPS LP 10-MSOP 制造商:Analog Devices 功能描述:CONVERTER - ADC |
发布紧急采购，3分钟左右您将得到回复。