- 您现在的位置：买卖IC网 > PDF目录8657 > AD9114BCPZRL7 (Analog Devices Inc)IC DAC DUAL 8BIT LO PWR 40LFCSP PDF资料下载
参数资料
| 型号： | AD9114BCPZRL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 42/52页 |
| 文件大小： | 0K |
| 描述： | IC DAC DUAL 8BIT LO PWR 40LFCSP |
| 产品培训模块： | Data Converter Fundamentals DAC Architectures |
| 标准包装： | 750 |
| 系列： | TxDAC® |
| 位数： | 8 |
| 数据接口： | 串行 |
| 转换器数目： | 2 |
| 电压电源： | 模拟和数字 |
| 功率耗散（最大）： | 232mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 40-LFCSP-VQ（6x6） |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 4 电流，单极 |
| 采样率（每秒）： | 125M |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页当前第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
Data Sheet
AD9114/AD9115/AD9116/AD9117
Rev. C | Page 47 of 52
APPLICATIONS INFORMATION
OUTPUT CONFIGURATIONS
The following sections illustrate some typical output configu-
rations for the AD9114/AD9115/AD9116/AD9117. Unless
otherwise noted, it is assumed that IxOUTFS is set to a nominal
20 mA. For applications requiring the optimum dynamic
performance, a differential output configuration is suggested.
A differential output configuration can consist of either an RF
transformer or a differential op amp configuration. The trans-
former configuration provides the optimum high frequency
performance and is recommended for any application that
allows ac coupling. The differential op amp configuration is
suitable for applications requiring dc coupling, signal gain,
and/or a low output impedance.
A single-ended output is suitable for applications in which low
cost and low power consumption are primary concerns.
DIFFERENTIAL COUPLING USING A TRANSFORMER
An RF transformer can be used to perform a differential-to-
single-ended signal conversion, as shown in Figure 102. The
distortion performance of a transformer typically exceeds
that available from standard op amps, particularly at higher
frequencies. Transformer coupling provides excellent rejection
of common-mode distortion (that is, even-order harmonics)
over a wide frequency range. It also provides electrical isolation
and can deliver voltage gain without adding noise. Transformers
with different impedance ratios can also be used for impedance
matching purposes. The main disadvantages of transformer
coupling are low frequency roll-off, lack of power gain, and
high output impedance.
AD9114/AD9115/
AD9116/AD9117
IOUTN
IOUTP
29
28
OPTIONAL RDIFF
RLOAD
07466-
063
Figure 102. Differential Output Using a Transformer
The center tap on the primary side of the transformer must be
connected to a voltage that keeps the voltages on IOUTP and
IOUTN within the output common-mode voltage range of the
device. Note that the dc component of the DAC output current
is equal to IIOUTFS and flows out of both IOUTP and IOUTN.
The center tap of the transformer should provide a path for this
dc current. In most applications, AGND provides the most
convenient voltage for the transformer center tap. The comple-
mentary voltages appearing at IOUTP and IOUTN (that is,
VIOUTP and VIOUTN) swing symmetrically around AGND and
should be maintained with the specified output compliance
range of the AD9114/AD9115/AD9116/AD9117.
A differential resistor, RDIFF, can be inserted in applications in
which the output of the transformer is connected to the load,
RLOAD, via a passive reconstruction filter or cable. RDIFF, as
reflected by the transformer, is chosen to provide a source
termination that results in a low voltage standing wave ratio
(VSWR). Note that approximately half the signal power is
dissipated across RDIFF.
SINGLE-ENDED BUFFERED OUTPUT USING
AN OP AMP
An op amp, such as the ADA4899-1, can be used to perform a single-
ended current-to-voltage conversion, as shown in Figure 103.
Figure 103 is a simplified schematic. The REFIO pin must be
buffered to keep the load current less than 100 nA. The AD9114/
AD9115/AD9116/AD9117 are configured with a pair of series
resistors, RS, off each output. For best distortion performance, RS
should be set to 0 Ω. The feedback resistor, RFB, determines the
peak-to-peak signal swing by the formula
VOUT = RFB × IFS
The common-mode voltage of the output is determined by the
formula
2
1
FS
FB
B
FB
REF
CM
I
R
V
×
+
×
=
The maximum and minimum voltages out of the amplifier are,
respectively,
+
×
=
B
FB
REF
MAX
R
V
1
VMIN = VMAX IFS × RFB
+5V
AD9114/AD9115/
AD9116/AD9117
IOUTP
IOUTN 29
RFB
VOUT
REFIO 34
28
RS
AVSS 25
CF
C
RS
RB
+
–
ADA4899-1
–5V
07466-
064
Figure 103. Single-Supply, Single-Ended Buffer
相关PDF资料 |
PDF描述 |
|---|---|
| IDT49FCT3805QI | IC CLK BUFFER 1:5 100MHZ 20-QSOP |
| V110A15H400BG2 | CONVERTER MOD DC/DC 15V 400W |
| VI-J6Y-MY | CONVERTER MOD DC/DC 3.3V 33W |
| VI-J0H-MX-B1 | CONVERTER MOD DC/DC 52V 75W |
| VI-J6Y-MX | CONVERTER MOD DC/DC 3.3V 49.5W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9114-DPG2-EBZ | 功能描述:IC DAC DUAL 8BIT LO PWR 40LFCSP RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:TxDAC® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9114-EBZ | 制造商:Analog Devices 功能描述:DUAL 8 BIT LOW POWER CONVERTER - Boxed Product (Development Kits) |
| AD9115 | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual, 8-/10-/12-/14-Bit Low Power Digital-to-Analog Converters |
| AD91151Z | 制造商:Analog Devices 功能描述: |
| AD91154Z | 制造商:Analog Devices 功能描述:SCREENED DSP PART - Rail/Tube |
发布紧急采购，3分钟左右您将得到回复。