参数资料
| 型号： | AD9148BBPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 39/72页 |
| 文件大小： | 0K |
| 描述： | IC DAC 16BIT SPI/SRL 196BGA |
| 标准包装： | 1 |
| 系列： | TxDAC+® |
| 设置时间： | 20ns |
| 位数： | 16 |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 4 |
| 电压电源： | 单电源 |
| 功率耗散（最大）： | 2.67W |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 196-LFBGA 裸露焊盘 |
| 供应商设备封装： | 196-BGA |
| 包装： | 托盘 |
| 输出数目和类型： | 4 电流，单极 |
| 采样率（每秒）： | 1G |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页当前第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
AD9148
Data Sheet
Rev. B | Page 44 of 72
No Synchronization
In this mode, Bit 7 in Register 0x10 is set to 0, the pipeline delay
in the signal processing is not controlled, and the read pointer
of the FIFO is never reset. However, to assure that the FIFO can
operate safely and there is no concurrent access to FIFO from
the write and read pointer to the same address, it is important
to ensure that the phase offset between the two pointers is greater
than 2. In consequence, the only FIFO reset that can be used
safely is the data rate synchronization, Bit 6 of Register 0x10 set
to 0, where the FIFO is reset with a fixed offset of 4 between the
write and read pointers. Because there is no SYNC signal, the
reset of the FIFO write pointer can only be done by a FRAME
signal or an SPI command.
FIFO Reset Commands
Depending on the configuration of the system, the FIFO reset
can be done manually or periodically for a multichip system.
The AD9148 provides two ways to resetting the FIFO pointers:
SPI interface or periodic reset using the FRAME signal.
The SPI also gives access to each FIFO phase offset in Bits [2:0]
of the corresponding FIFO status/control registers, Register 0x17
and Register 0x19. The value in these three bits corresponds either
to the offset between the write and read pointer in the data rate
synchronization or to the absolute address of the FIFO write
pointer in the FIFO rate synchronization.
SPI Command for Manual Reset
If a manual reset is acceptable, the FIFO pointer addresses can
be reset using the SPI interface.
To initialize the FIFO data level through the SPI, Bit 3 of
Register 0x17 (FIFO Port A) or Bit 3 of Register 0x19 (FIFO
Port B) should be toggled from 0 to 1 and back. When the
write to the register is complete, the corresponding FIFO data
level is initialized.
The recommended procedure for a SPI FIFO data level
initialization is
1. Request FIFO Port A or FIFO Port B level reset by setting
Bit 3 in Register 0x17 or Bit 3 in Register 0x19 to Logic 1. The
FIFO phase offset, Bits [2:0] in Register 0x17 or Bits [2:0] in
Register 0x19, should also be written at the same time to
set the desired value of offset between the FIFO write and
read pointers.
2. Verify that the part acknowledges the request by ensuring
that Bit 4 in Register 0x17 or Bit 4 in Register 0x19 is set
to Logic 1.
3. Remove the request by resetting Bit 3, Register 0x17 or Bit 3,
Register 0x19 to 0.
4. The FIFO SPI aligned flag in the Event Flag 0 register, Bit 2
in Register 0x06, is set when the reset of the write pointer has
been realized. Bit 4 in Register 0x17 or Bit 4 in Register 0x19 is
reset to 0 to indicate which FIFO has generated this flag.
Note that the SPI writes to Register 0x17 or Register 0x19 should
be done while maintaining a constant value in the FIFO phase
offset bits.
FIFO Reset Using FRAME Signal
The FIFO pointers can also be reset using the FRAME signals.
If only one DCI is used, only the FRAMEA signal is used for the
FIFO reset. This mode is enabled by setting Bit 6 in Register 0x10.
As discussed in the FIFO Synchronization Modes section, the
FRAME input is used to initialize the FIFO data level value. When
the FRAME signal is asserted high for at least the time interval
needed to load the complete data to the four DACs, the write
pointer is reset depending on the mode of synchronization chosen.
Data rate synchronization (default), Bit 6 of Register 0x10,
is set to 0. When read pointer reaches 0, write pointer reset
to FIFO offset phase.
FIFO rate synchronization, Bit 6 of Register 0x10, is set to 1.
On the rising edge of the FRAME signal, write pointer
reset to FIFO start level.
MONITORING THE FIFO STATUS
The FIFO initialization and status can be read from Register 0x17.
This register provides information about the FIFO initialization
method and whether the initialization was successful. The MSB
of Register 0x17 is a FIFO warning flag that can optionally trigger a
device IRQ. This flag is an indication that the FIFO is close to
emptying (FIFO level is 1) or overflowing (FIFO level is 7). This
is an indication that the data may soon be corrupted, and action
should be taken.
The FIFO data level can be read from Register 0x18 at any time.
The SPI reported FIFO data level is denoted as a 7-bit thermometer
code of the write counter state relative to the absolute read counter
being 0. The optimum FIFO data level of four is, therefore,
reported as a value of 00001111 in the status register.
Note that, depending on the timing relationship between DCI
and the main DACCLK, the FIFO level value can be off by a ±1
count. Therefore, it is important to keep the difference between the
read and write points to at least 2.
相关PDF资料 |
PDF描述 |
|---|---|
| MS27473T10B98PBLC | CONN HSG PLUG 6POS STRGHT PINS |
| LTC2758ACLX#PBF | IC DAC 18BIT SPI/SRL 48-LQFP |
| MS27468T15B19PLC | CONN HSG RCPT 19POS JAMNUT PINS |
| V24B5M200BF2 | CONVERTER MOD DC/DC 5V 200W |
| MS27656T23B35B | CONN HSG RCPT 100POS WALL MT SCK |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9148BBPZRL | 功能描述:IC DAC 16BIT SPI/SRL 196BGA RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:TxDAC+® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 设置时间:1µs 位数:8 数据接口:串行 转换器数目:8 电压电源:双 ± 功率耗散（最大）:941mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC W 包装:带卷 (TR) 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD9148BPCZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad 16-Bit,1 GSPS, TxDAC+ Digital-to-Analog Converter |
| AD9148BPCZRL | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad 16-Bit,1 GSPS, TxDAC+ Digital-to-Analog Converter |
| AD9148-EBZ | 功能描述:BOARD EVALUATION FOR AD9148 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:TxDAC+® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
| AD9148-M5372-EBZ | 功能描述:BOARD EVAL FOR AD9149, ADL5372 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
发布紧急采购，3分钟左右您将得到回复。