- 您现在的位置：买卖IC网 > PDF目录10516 > AD9286BCPZ-500 (Analog Devices Inc)IC ADC 8BIT SPI/SRL 500M 48LFSCP PDF资料下载
参数资料
| 型号： | AD9286BCPZ-500 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 13/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 8BIT SPI/SRL 500M 48LFSCP |
| 标准包装： | 1 |
| 位数： | 8 |
| 采样率（每秒）： | 500M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 330mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 48-LFCSP-VQ（7x7） |
| 包装： | 托盘 |
| 输入数目和类型： | 2 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD9286
Data Sheet
Rev. B | Page 20 of 28
SERIAL PORT INTERFACE (SPI)
The AD9286 serial port interface (SPI) allows the user to configure
the converter for specific functions or operations through a
structured register space provided inside the ADC. The SPI
gives the user added flexibility and customization, depending
on the application. Addresses are accessed via the serial port
and can be written to or read from via the port. Memory is
organized into bytes that can be further divided into fields,
which are documented in the Memory Map section. For detailed
operational information, see the AN-877 Application Note,
Interfacing to High Speed ADCs via SPI.
CONFIGURATION USING THE SPI
Three pins define the SPI of this ADC: SCLK, SDIO, and CSB
(see Table 10). SCLK (a serial clock) is used to synchronize the
read and write data presented from and to the ADC. SDIO
(serial data input/output) is a dual-purpose pin that allows data
to be sent to and read from the internal ADC memory map
registers. CSB (chip select bar) is an active low control that
enables or disables the read and write cycles.
Table 10. Serial Port Interface Pins
Pin
Function
SCLK
Serial clock. A serial shift clock input that is used to
synchronize serial interface reads and writes.
SDIO
Serial data input/output. A dual-purpose pin that
typically serves as an input or an output, depending
on the instruction being sent and the relative position
in the timing frame.
CSB
Chip select bar. An active low control that gates the read
and write cycles.
The falling edge of CSB, in conjunction with the rising edge of
SCLK, determines the start of the framing. An example of the
serial timing and its definitions can be found in Figure 33.
Other modes involving CSB are available. The CSB pin can be held
low indefinitely, which permanently enables the device; this is
called streaming. CSB can stall high between bytes to allow for
additional external timing. When the CSB pin is tied high, SPI
functions are placed in high impedance mode. This mode turns
on any SPI pin secondary functions.
During the instruction phase, a 16-bit instruction is transmitted.
Data follows the instruction phase, and its length is determined
by the W0 and W1 bits, as shown in Figure 33.
All data is composed of 8-bit words. The first bit of the first byte
in a multibyte serial data transfer frame indicates whether a read
command or a write command is issued. This allows the serial
data input/output (SDIO) pin to change direction, from an input
to an output, at the appropriate point in the serial frame.
In addition to word length, the instruction phase determines
whether the serial frame is a read or write operation, allowing
the serial port to be used both to program the chip and to read
the contents of the on-chip memory. If the instruction is a readback
operation, the serial data input/output (SDIO) pin changes
direction, from an input to an output, at the appropriate point
in the serial frame.
Data can be sent in MSB-first mode or in LSB-first mode. MSB
first is the default on power-up and can be changed via the SPI
port configuration register. For more information about this
and other features, see the AN-877 Application Note, Interfacing
to High Speed ADCs via SPI.
DON’T CARE
SDIO
SCLK
CSB
tS
tDH
tCLK
tDS
tH
R/W
W1
W0
A12
A11
A10
A9
A8
A7
D5
D4
D3
D2
D1
D0
tLOW
tHIGH
093
38-
00
4
Figure 33. Serial Port Interface Timing Diagram
相关PDF资料 |
PDF描述 |
|---|---|
| UP050B821K-KFC | CAP CER 820PF 50V 10% AXIAL |
| VE-B4B-MX-F3 | CONVERTER MOD DC/DC 95V 75W |
| MAX3450EEUD+ | TXRX USB +/-15KV ESD 14-TSSOP |
| VE-B4B-MX-F1 | CONVERTER MOD DC/DC 95V 75W |
| AD976ABNZ | IC ADC 16BIT 200KSPS 28-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9286BCPZRL7-500 | 功能描述:IC ADC 8BIT SPI/SRL 500M 48LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD9287 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad, 8-Bit, 100 MSPS Serial LVDS 1.8 V A/D Converter |
| AD9287-100EB | 制造商:Analog Devices 功能描述: |
| AD9287-100EB1 | 制造商:AD 制造商全称:Analog Devices 功能描述:High Speed ADC USB FIFO Evaluation Kit |
| AD9287-100EBZ | 功能描述:BOARD EVALUATION AD9287 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
发布紧急采购，3分钟左右您将得到回复。