- 您现在的位置：买卖IC网 > PDF目录10516 > AD9286BCPZ-500 (Analog Devices Inc)IC ADC 8BIT SPI/SRL 500M 48LFSCP PDF资料下载
参数资料
| 型号： | AD9286BCPZ-500 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 19/28页 |
| 文件大小： | 0K |
| 描述： | IC ADC 8BIT SPI/SRL 500M 48LFSCP |
| 标准包装： | 1 |
| 位数： | 8 |
| 采样率（每秒）： | 500M |
| 数据接口： | 串行，SPI? |
| 转换器数目： | 2 |
| 功率耗散（最大）： | 330mW |
| 电压电源： | 模拟和数字 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 48-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 48-LFCSP-VQ（7x7） |
| 包装： | 托盘 |
| 输入数目和类型： | 2 个差分，双极 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页当前第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
AD9286
Data Sheet
Rev. B | Page 26 of 28
APPLICATIONS INFORMATION
DESIGN GUIDELINES
Before starting design and layout of the AD9286 as a system,
it is recommended that the designer become familiar with these
guidelines, which discuss the special circuit connections and
layout requirements that are needed for certain pins.
Power and Ground Recommendations
When connecting power to the AD9286, it is strongly recom-
mended that two separate supplies be used. Use one 1.8 V supply
for analog (AVDD); use a separate 1.8 V supply for the digital
output supply (DRVDD). If a common 1.8 V AVDD and DRVDD
supply must be used, the AVDD and DRVDD domains must be
isolated with a ferrite bead or filter choke and separate decoupling
capacitors. Several different decoupling capacitors can be used
to cover both high and low frequencies. Locate these capacitors
close to the point of entry at the printed circuit board (PCB)
level and close to the pins of the part, with minimal trace length.
A single PCB ground plane should be sufficient when using the
AD9286. With proper decoupling and smart partitioning of the
PCB analog, digital, and clock sections, optimum performance
is easily achieved.
Exposed Paddle Thermal Heat Sink Recommendations
The exposed paddle (Pin 0) is the only ground connection
for the AD9286; therefore, it must be connected to analog
ground (AGND) on the customer PCB. To achieve the best
electrical and thermal performance, mate an exposed (no
solder mask), continuous copper plane on the PCB to the
AD9286 exposed paddle, Pin 0.
The copper plane should have several vias to achieve the
lowest possible resistive thermal path for heat dissipation
to flow through the bottom of the PCB. Fill or plug these
vias with nonconductive epoxy.
To maximize the coverage and adhesion between the ADC and
the PCB, a silkscreen should be overlaid to partition the continuous
plane on the PCB into several uniform sections. This provides
several tie points between the ADC and the PCB during the reflow
process. Using one continuous plane with no partitions guarantees
only one tie point between the ADC and the PCB. For detailed
information about packaging and PCB layout of chip scale
packages, see the AN-772 Application Note, A Design and
Manufacturing Guide for the Lead Frame Chip Scale Package
(LFCSP), at www.analog.com.
VCM
The VCM pin should be decoupled to ground with a 0.1 μF
capacitor.
RBIAS
The AD9286 requires that a 10 k resistor be placed between
the RBIAS pin and ground. This resistor, which sets the master
current reference of the ADC core, should have at least a 1%
tolerance.
Reference Decoupling
Decouple the VREF pin externally to ground with a low ESR,
1.0 μF capacitor in parallel with a low ESR, 0.1 μF ceramic
capacitor.
SPI Port
The SPI port should not be active during periods when the full
dynamic performance of the converter is required. Because the
SCLK, CSB, and SDIO signals are typically asynchronous to the
ADC clock, noise from these signals can degrade converter
performance. If the on-board SPI bus is used for other devices,
it may be necessary to provide buffers between this bus and the
AD9286 to prevent these signals from transitioning at the converter
inputs during critical sampling periods.
相关PDF资料 |
PDF描述 |
|---|---|
| UP050B821K-KFC | CAP CER 820PF 50V 10% AXIAL |
| VE-B4B-MX-F3 | CONVERTER MOD DC/DC 95V 75W |
| MAX3450EEUD+ | TXRX USB +/-15KV ESD 14-TSSOP |
| VE-B4B-MX-F1 | CONVERTER MOD DC/DC 95V 75W |
| AD976ABNZ | IC ADC 16BIT 200KSPS 28-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9286BCPZRL7-500 | 功能描述:IC ADC 8BIT SPI/SRL 500M 48LFCSP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 模数转换器 系列:- 标准包装:1 系列:- 位数:14 采样率（每秒）:83k 数据接口:串行，并联 转换器数目:1 功率耗散（最大）:95mW 电压电源:双 ± 工作温度:0°C ~ 70°C 安装类型:通孔 封装/外壳:28-DIP（0.600"，15.24mm） 供应商设备封装:28-PDIP 包装:管件 输入数目和类型:1 个单端，双极 |
| AD9287 | 制造商:AD 制造商全称:Analog Devices 功能描述:Quad, 8-Bit, 100 MSPS Serial LVDS 1.8 V A/D Converter |
| AD9287-100EB | 制造商:Analog Devices 功能描述: |
| AD9287-100EB1 | 制造商:AD 制造商全称:Analog Devices 功能描述:High Speed ADC USB FIFO Evaluation Kit |
| AD9287-100EBZ | 功能描述:BOARD EVALUATION AD9287 RoHS:是 类别:编程器，开发系统 >> 评估板 - 模数转换器 (ADC) 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:- ADC 的数量:1 位数:12 采样率（每秒）:94.4k 数据接口:USB 输入范围:±VREF/2 在以下条件下的电源（标准）:- 工作温度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，软件 |
发布紧急采购，3分钟左右您将得到回复。