- 您现在的位置：买卖IC网 > PDF目录17065 > AD9787-DPG2-EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD9787 PDF资料下载
参数资料
| 型号： | AD9787-DPG2-EBZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 27/64页 |
| 文件大小： | 0K |
| 描述： | BOARD EVALUATION FOR AD9787 |
| 标准包装： | 1 |
| 系列： | * |
| DAC 的数量： | 2 |
| 位数： | 14 |
| 采样率（每秒）： | 800M |
| 数据接口： | 串行 |
| 设置时间： | 22ms |
| DAC 型： | 电流 |
| 工作温度： | -40°C ~ 85°C |
| 已供物品： | * |
| 已用 IC / 零件： | AD9787 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页
AD9785/AD9787/AD9788
Rev. A | Page 33 of 64
INPUT DATA PORTS
The AD9785/AD9787/AD9788 can operate in two data input
modes: dual-port mode and single-port mode. In the default
dual-port mode (single-port mode = 0), each DAC receives data
from a dedicated input port. In single-port mode (single-port
mode = 1), both DACs receive data from Port 1. In single-port
mode, DAC 1 and DAC 2 data is interleaved and the TXENABLE
input is used to steer data to the intended DAC. In dual-port
mode, the TXENABLE input is used to power down the digital
datapath.
In dual-port mode, the data must be delivered at the input data
rate. In single-port mode, data must be delivered at twice the
input data rate of each DAC. Because the data inputs function up
to a maximum of 300 MSPS, it is only practical to operate with
input data rates up to 150 MHz per DAC in single-port mode.
In both dual-port and single-port modes, a data clock output
(DATACLK) signal is available as a fixed-time base with which
to drive data from an FPGA (field programmable gate array) or
from another data source. This output signal operates at the
input data rate. The DATACLK pin can operate as either an
input or an output.
SINGLE-PORT MODE
In single-port mode, data for both DACs is received on the
Port 1 input bus (P1D[15:0]). I and Q data samples are inter-
leaved and are latched on the rising edges of DATACLK.
Accompanying the data is the TXENABLE (Pin 39) input
signal, which steers incoming data to its respective DAC. When
TXENABLE is high, the corresponding data-word is sent to the
I DAC and, when TXENABLE is low, the corresponding data is
sent to the Q DAC. The timing of the digital interface in
interleaved mode is shown in Figure 48.
The Q first bit (Register 0x01, Bit 1) controls the pairing
order of the input data. With the Q first bit set to the default
of 0, the I/Q pairing sent to the DACs is the two input data-
words corresponding to TXENABLE low followed by
TXENABLE high.
With the Q first bit set to 1, the I/Q pairing sent to the DACs is
the two input data-words corresponding to TXENABLE high
followed by TXENABLE low. Note that with Q first set, the
I data still corresponds to the TXENABLE high word and the
Q data corresponds to the TXENABLE low word and only the
pairing order changes.
DUAL-PORT MODE
In dual-port mode, data for each DAC is received on the
respective input bus (P1D[15:0] or P2D[15:0]). I and Q data
arrive simultaneously and are sampled on the rising edge of an
internal sampling clock (SMP_CLK) that is synchronous with
DATACLK. In dual-port mode, driving the TXENABLE input
low powers down the digital datapath. TXENABLE should be
held high during normal data transmission.
INPUT DATA REFERENCED TO DATACLK
The simplest method of interfacing to the AD9785/AD9787/
AD9788 is when the input data is referenced to the DATACLK
output. The DATACLK output is phase-locked (with some
offset) to the internal clock that is used to latch the input data.
Therefore, if the setup and hold times of the input data with
respect to DATACLK are met, the interface timing latches in the
data correctly.
Table 25 shows the setup and hold time requirements for the
input data over the operating temperature range of the device.
Table 25 also shows the data valid window (DVW). The data
valid window is the sum of the setup and hold times of the
interface. This is the minimum amount of time valid data must
be presented to the device in order to ensure proper sampling.
相关PDF资料 |
PDF描述 |
|---|---|
| ESA10DTKS | CONN EDGECARD 20POS DIP .125 SLD |
| SDR0604-331KL | INDUCTOR POWER 330UH 10% SMD |
| AD9788-DPG2-EBZ | BOARD EVALUATION FOR AD9788 |
| SLPX223M025E7P3 | CAP ALUM 22000UF 25V 20% SNAP |
| EMA10DTKS | CONN EDGECARD 20POS DIP .125 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9787-EBZ | 制造商:Analog Devices 功能描述:DUAL 16B, D-A CONVERTER - Bulk |
| AD9788 | 制造商:AD 制造商全称:Analog Devices 功能描述:Dual 12-/14-/16-Bit 800 MSPS DAC with Low Power 32-Bit Complex NCO |
| AD9788BSVZ | 功能描述:IC DAC 16BIT 800MSPS 100TQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:TxDAC® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:50 系列:- 设置时间:4µs 位数:12 数据接口:串行 转换器数目:2 电压电源:单电源 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-uMAX 包装:管件 输出数目和类型:2 电压，单极 采样率（每秒）:* 产品目录页面:1398 (CN2011-ZH PDF) |
| AD9788BSVZRL | 功能描述:IC DAC 16BIT 800MSPS 100TQFP RoHS:是 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:TxDAC® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 设置时间:1µs 位数:8 数据接口:串行 转换器数目:8 电压电源:双 ± 功率耗散（最大）:941mW 工作温度:0°C ~ 70°C 安装类型:表面贴装 封装/外壳:24-SOIC（0.295"，7.50mm 宽） 供应商设备封装:24-SOIC W 包装:带卷 (TR) 输出数目和类型:8 电压，单极 采样率（每秒）:* |
| AD9788-DPG2-EBZ | 功能描述:BOARD EVALUATION FOR AD9788 RoHS:是 类别:编程器，开发系统 >> 评估板 - 数模转换器 (DAC) 系列:* 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:- DAC 的数量:4 位数:12 采样率（每秒）:- 数据接口:串行，SPI? 设置时间:3µs DAC 型:电流/电压 工作温度:-40°C ~ 85°C 已供物品:板 已用 IC / 零件:MAX5581 |
发布紧急采购，3分钟左右您将得到回复。