- 您现在的位置：买卖IC网 > PDF目录11768 > AD9983AKCPZ-140 (Analog Devices Inc)IC INTRFACE 8BIT 140MSPS 64LFCSP PDF资料下载
参数资料
| 型号： | AD9983AKCPZ-140 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 32/44页 |
| 文件大小： | 0K |
| 描述： | IC INTRFACE 8BIT 140MSPS 64LFCSP |
| 标准包装： | 1 |
| 应用： | 视频 |
| 接口： | 模拟 |
| 电源电压： | 1.7 V ~ 3.47 V |
| 封装/外壳： | 64-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 64-LFCSP-VQ（9x9） |
| 包装： | 管件 |
| 安装类型： | 表面贴装 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
AD9983A
Rev. 0 | Page 38 of 44
0x2C—Bits[7:5] Auto-Offset Hold
Must be written to 0x00 for proper operation.
0x2C—Bit[4] Auto-Offset Hold
A bit for controlling whether the auto-offset function runs
continuously or runs once and holds the result. Continuous
updates are recommended because this allows the AD9983A to
compensate for drift over time and temperature. If one-time
updates are preferred, these should be performed every time the
part is powered up and when there is a mode change. To do a
one-time update, first auto-offset must be enabled (Register
0x1B, Bit 5). Next, this bit (auto-offset hold) must first be set to
1 to let the auto-offset function operate and settle to a final
value. Auto-offset hold should then be set to 0 to hold the offset
values that the auto circuitry calculates. The AD9983A auto-
offset circuit’s maximum settle time is 10 updates. For example,
if the update frequency is set to once every 64 Hsyncs, then the
maximum settling time would be 640 Hsyncs (10 × 64 Hsyncs).
Table 77. Auto-Offset Hold
Select
Result
0
Disables auto-offset updates and holds the
current auto-offset values
1
Allows auto-offset to update continuously
0x2C—Bits[3:0]
Must be written to 0x0 for proper operation.
0x2D—Bits[7:0] Test Register 5
Read/write bits for future use. Must be written to 0xE8 for
proper operation.
0x2E—Bits[7:0] Test Register 6
Read/write bits for future use. Must be written to 0xE0 for
proper operation.
0x34—Bit[2] SOG Filter Enable
This bit enables the SOG filter, which will reject inputs with a
width of less than 250 ns. This aids the PLL in the ability to
ignore extraneous (non-valid) sync pulses.
Table 78. SOG Filter Enable
Select
Result
0
SOG filter disabled
1
SOG filter enabled
0x36—Bit[0] VCO Gear Select
This bit allows the VCO to select a lower ‘gear’ which enables it
to run lower pixel clocks while remaining in a more linear range.
Table 79. VCO Gear Select
Select
Result
0
Normal VCO setting
1
Enables lower VCO clock output
0x3C—Bits[7:4] Test Bits
Must be set to 0x0 for proper operation.
0x3C—Bit[3] Auto Gain Matching Hold
A bit for controlling whether the auto gain matching function
runs continuously or runs once and holds the result.
Continuous updates are recommended because it allows the
AD9983A to compensate for drift over time and temperature.
If one-time updates are preferred, these should be performed
every time the part is powered up and when there is a mode
change. To do a one-time update, first auto gain matching must
be enabled (Register Ox3C, Bit 2). Next, this bit (Auto Gain
Matching Hold) must first be set to 1 to let the auto gain
matching function operate and settle to a final value. The Auto
Gain Matching Hold bit should then be set to 0 to hold the gain
values that the auto circuitry calculates. The AD9983A auto gain
matching circuit’s maximum settle time is 10 updates. For example,
if the update frequency is set to once every 64 Hsyncs, then the
maximum settling time would be 640 Hsyncs (10 x 64 Hsyncs).
Table 80. Auto Gain Hold
Select
Result
0
Disables auto gain updates and holds the
current auto offset values
1
Allows auto gain to update continuously
The power-up default setting is 0.
0x3C—Bits[2:0] Auto Gain Matching Enable
These bits enable or disable the auto gain matching function.
When set to 000, the auto gain matching function is disabled;
when set to 110 the auto gain matching function is enabled.
Table 81. Auto Gain Matching Enable
Select
Result
000
Auto gain matching disabled
110
Auto gain matching enabled
相关PDF资料 |
PDF描述 |
|---|---|
| V150B24H150BG | CONVERTER MOD DC/DC 24V 150W |
| 5227079-5 | CONN PLUG BNC RG58 CRIMP AU |
| VE-JTM-IW-F1 | CONVERTER MOD DC/DC 10V 100W |
| VE-JT1-IW-F4 | CONVERTER MOD DC/DC 12V 100W |
| MS27474E14B35SD | CONN RCPT 37POS JAM NUT W/SCKT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AD9983AKCPZ-1401 | 制造商:AD 制造商全称:Analog Devices 功能描述:High Performance 8-Bit Display Interface |
| AD9983AKCPZ-170 | 功能描述:IC INTRFACE 8BIT 170MSPS 64LFCSP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| AD9983AKCPZ-1701 | 制造商:AD 制造商全称:Analog Devices 功能描述:High Performance 8-Bit Display Interface |
| AD9983AKSTZ-140 | 功能描述:IC DISPLAY 8BIT 140MSPS 80LQFP RoHS:是 类别:集成电路 (IC) >> 接口 - 专用 系列:- 特色产品:NXP - I2C Interface 标准包装:1 系列:- 应用:2 通道 I²C 多路复用器 接口:I²C，SM 总线 电源电压:2.3 V ~ 5.5 V 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:剪切带 (CT) 安装类型:表面贴装 产品目录页面:825 (CN2011-ZH PDF) 其它名称:568-1854-1 |
| AD9983AKSTZ-1401 | 制造商:AD 制造商全称:Analog Devices 功能描述:High Performance 8-Bit Display Interface |
发布紧急采购，3分钟左右您将得到回复。