- 您现在的位置：买卖IC网 > PDF目录20620 > ADE7166ASTZF16 (Analog Devices Inc)IC ENERGY METER 1PHASE 64LQFP PDF资料下载
参数资料
| 型号： | ADE7166ASTZF16 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 110/152页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METER 1PHASE 64LQFP |
| 标准包装： | 1 |
| 输入阻抗： | * |
| 测量误差： | * |
| 电压 - 高输入/输出： | * |
| 电压 - 低输入/输出： | * |
| 电流 - 电源： | * |
| 电源电压： | * |
| 测量仪表类型： | * |
| 工作温度： | * |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 64-LQFP |
| 供应商设备封装： | 64-LQFP（10x10） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页当前第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页
ADE7116/ADE7156/ADE7166/ADE7169/ADE7566/ADE7569
ECON
COMMAND
ADDRESS
EADRH EADRL
ADDRESS
DECODER
PROTECTION
DECODER
ACCESS
ALLOWED?
TRUE: ACCESS
ALLOWED
ECON = 0
FLASH
PROTECTION KEY
FLSHKY
FLSHKY = 0 × 3B?
FALSE: ACCESS
DENIED
ECON = 1
Figure 95. Flash Memory Read/Write/Erase Protection Block Diagram
ECON—Flash Control SFR
Programming flash memory is done through the Flash Control
SFR (ECON, Address 0xB9). This SFR allows the user to read,
write, erase, or verify the 16 kB of flash memory. As a method of
security, a key must be written to the FLSHKY, Address 0xBA)
to initiate any user access to the flash memory. Upon completion
of the flash memory operation, the FLSHKY SFR is reset such that
it must be written to before another flash memory operation.
Requiring the key to be set before an access to the flash memory
decreases the likelihood of user code or data being overwritten
by a runaway program.
Table 102. Flash Control SFR (ECON, Address 0xB9)
The program counter, PC, is held on the instruction where the
ECON SFR is written to until the flash memory controller is
done performing the requested operation. Then, the PC
increments to continue with the next instruction.
Any interrupt requests that occur while the flash controller is
performing an operation are not handled until the flash operation
is complete. All peripherals, such as timers and counters, continue
to operate as configured throughout the flash memory access.
Bit
[7:0]
Mnemonic
ECON
Default
0
Value
1
Description
Write byte. The value in EDATA is written to the flash memory at the page address given by
EADRH (Address 0xC7) and EADRL (Address 0xC6). Note that the byte being addressed must be
pre-erased.
2
3
4
5
8
Erase page. A 512-byte page of flash memory address is erased. The page is selected by the
address in EADRH and EADRL. Any address in the page can be written to EADRH and EADRL to
select it for erasure.
Erase all. All 16 kB of the available flash memory are erased. Note that this command is used
during serial mode and parallel download mode but should not be executed by user code.
Read byte. The byte in the flash memory addressed by EADRH/EADRL is read into EDATA.
Erase Page and Write Byte. The page that holds the byte addressed by EADRH/EADRL is erased.
Data in EDATA is then written to the byte of flash memory addressed by EADRH/EADRL.
Protect code (see the Protecting the Flash section).
Table 103. Flash Key SFR (FLSHKY, Address 0xBA)
Bit
[7:0]
Mnemonic
FLSHKY
Default
0xFF
Description
The content of this SFR is compared to the flash key, 0x3B. If the two values match, the next ECON
operation is allowed (see the Protecting the Flash section).
Table 104. Flash Protection Key SFR (PROTKY, Address 0xBB)
Bit
[7:0]
Mnemonic
PROTKY
Default
0xFF
Description
The content of this SFR is compared to the flash memory location at Address 0x3FFA. If the two values
match, the update of the write/erase and read protection setup is allowed (see the Protecting the Flash
section).
If the protection key in the flash is 0xFF, the PROTKY SFR value is not used for comparison. This SFR is
also used to write the protection key in the flash. This is done by writing the desired value in PROTKY
and by writing 0x08 in the ECON SFR. This operation can only be done once.
Table 105. Flash Data SFR (EDATA, Address 0xBC)
Bit
[7:0]
Mnemonic
EDATA
Default
0
Description
Flash pointer data.
Rev. B | Page 110 of 1 52
相关PDF资料 |
PDF描述 |
|---|---|
| GMM06DTMI | CONN EDGECARD 12POS R/A .156 SLD |
| ISL2101AAR3Z-T | IC DVR HALF-BRDG HF 100V 2A 9DFN |
| GSM06DTMI | CONN EDGECARD 12POS R/A .156 SLD |
| LQW18AN15NJ00D | INDUCTOR 15NH 600MA 0603 |
| ADE7752AARZ-RL | IC ENERGY METERING 3PHASE 24SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7166ASTZF16-RL | 功能描述:IC ENERGY METER 1PHASE 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7166ASTZF8 | 功能描述:IC ENERGY METER 1PHASE 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7166ASTZF8-RL | 功能描述:IC ENERGY METER 1PHASE 64LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7169 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC and LCD driver |
| ADE7169ACPF16 | 制造商:AD 制造商全称:Analog Devices 功能描述:Single-Phase Energy Measurement IC with 8052 MCU, RTC and LCD driver |
发布紧急采购，3分钟左右您将得到回复。