- 您现在的位置：买卖IC网 > PDF目录20638 > ADE7754ARZ (Analog Devices Inc)IC ENERGY METERING 3PHASE 24SOIC PDF资料下载
参数资料
| 型号： | ADE7754ARZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 18/44页 |
| 文件大小： | 0K |
| 描述： | IC ENERGY METERING 3PHASE 24SOIC |
| 标准包装： | 31 |
| 输入阻抗： | 370 千欧 |
| 测量误差： | 0.1% |
| 电压 - 高输入/输出： | 2.4V |
| 电压 - 低输入/输出： | 0.8V |
| 电流 - 电源： | 7mA |
| 电源电压： | 4.75 V ~ 5.25 V |
| 测量仪表类型： | 3 相 |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC W |
| 包装： | 管件 |
| 产品目录页面： | 797 (CN2011-ZH PDF) |
| 配用： | EVAL-ADE7754EBZ-ND - BOARD EVALAUTION FOR ADE7754 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页
ADE7754
APOS[11:0]
I
HPF
SGN SGN SGN SGN SGN 2 10
2 4
2 3
2 2
2 1
2 0
ACTIVE POWER
SIGNAL – P
CURRENT SIGNAL – i(t)
–100% TO +100% FS
28F5C2h
00h
D70A3Eh
1V/GAIN1
MULTIPLIER
24
LPF2
28
+
12
D1B717h
V
1
INSTANTANEOUS
POWER SIGNAL – p(t)
AWG
VOLTAGE SIGNAL – v(t)
–100% TO + 100% FS
28F5h
00h
1V/GAIN2
D70Bh
Figure 24. Active Power Signal Processing
Figure 24 shows the signal processing in each phase for the
active power in the ADE7754.
Figure 25 shows the maximum code (hexadecimal) output
range of the active power signal (after AWG). Note that the
output range changes depending on the contents of the active
power gain and watt gain registers. See the Current Channel
ADC section. The minimum output range is given when the
active power gain and watt gain registers contents are equal to
800h, and the maximum range is given by writing 7FFh to the
active power gain and watt gain registers. These can be used to
calibrate the active power (or energy) calculation in the
ADE7754 for each phase and the total active energy. See the
Total Active Power Calculation section.
Reverse Power Information
The ADE7754 detects when the current and voltage channels
of any of the three phase inputs have a phase difference greater
than 90 ° (i.e., | A | or | B | or | C | > 90 ° ). This mechanism
can detect wrong connection of the meter or generation of
active energy.
The reverse power information is available for Phase A, Phase B,
and Phase C, respectively, by reading Bits 12 to 14 of the CFNUM
register. See Table XI. The state of these bits represents the
sign of the active power of the corresponding phase. Logic 1
corresponds to negative active power.
The AENERGY phase selection bits (WATSEL bits of the
WATMode register) enable the negative power detection per
ACTIVE
POWER
VOLTAGE CHANNEL
CURRENT CHANNEL
0.5V/GAIN2
0.5V/GAIN1
phase. If Phase A is enabled in the AENERGY accumulation,
Bit 5 of WATMode register sets to Logic 1 and the negative
power detection for Phase A—Bit 12 of CFNUM register—
13A92A4h
D1B717h
68DB8Ch
0000000h
972474h
2E48E9h
+ 150% FS
+ 100% F5
+ 50% FS
AAPGAIN[11:0] OR AWGAIN[11:0]
– 50% FS
– 100% FS
indicates the direction of the active energy. If Phase A is
disabled in the AENERGY register, the negative power bit for
Phase A is set to Logic 0.
TOTAL ACTIVE POWER CALCULATION
EC56D5Ch
000h
7FFh
800h
– 150% FS
The sum of the active powers coming from each phase provides
the total active power consumption. Different combinations of
Figure 25. Active Power Calculation Output Range
Power Offset Calibration
The ADE7754 also incorporates an active offset register on each
phase (AAPOS, BAPOS, and CAPOS). These are signed twos
complement 12-bit registers that can be used to remove offsets
in the active power calculations. An offset may exist in the
power calculation because of crosstalk between channels on the
PCB or in the IC itself. The offset calibration allows the con-
tents of the active power register to be maintained at zero when
no power is being consumed.
the three phases can be selected in the sum by setting Bits 7 and
6 of the WATMode register (mnemonic WATMOD[1:0]).
Figure 26 demonstrates the calculation of the total active power,
which depends on the configuration of the WATMOD bits in
the WATMode register. Each term of the formula can be disabled
or enabled by setting WATSEL bits respectively to Logic 0 or
Logic 1 in the WATMode register. The different configurations
are described in Table I.
Table I. Total Active Power Calculation
One LSB in the active power offset register is equivalent to one
WATMOD WATSEL0
WATSEL1
WATSEL2
LSB in the 28-bit energy bus displayed in Figure 24. Each
time power is added to the internal active energy register, the
content of the active power offset register is added. See the
Total Active Power Calculation section. Assuming the average
0d
1d
2d
V A
V A
V A
I A *
(I A * –I B * )
(I A * –I B * )
+ V B
+0
+0
I B *
+ V C
+ V C
+ V C
I C *
(I C * –I B * )
I C *
value from LPF2 is 8637BCh (8,796,092d) with full ac scale
inputs on current channel and voltage channel, then one LSB in
the LPF2 output is equivalent to 0.011% of measurement error
at –60 dB down of full scale. See the Calibration of a 3-Phase
Meter Based on the ADE7754 Application Note AN-624.
Note that I A * , I B * , and I C * represent the current channel
samples after APGAIN correction and high-pass filtering.
–18 –
REV. 0
相关PDF资料 |
PDF描述 |
|---|---|
| MAX8631YETI+ | IC LED DRVR WHITE BCKLGT 28-TQFN |
| EBC15DCMI-S288 | CONN EDGECARD 30POS .100 EXTEND |
| ISL6605IRZ-T | IC MOSFET DRVR SYNC BUCK 8-QFN |
| VI-J6F-CX-F1 | CONVERTER MOD DC/DC 72V 75W |
| PX3511BDAG-R3 | IC DRVR SYNC BUCK HF 8-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADE7754ARZRL | 功能描述:IC ENERGY METERING 3PHASE 24SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 能量测量 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:* |
| ADE7755 | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with Pulse Output |
| ADE7755AARSRL | 制造商:Analog Devices 功能描述:ENERGY METERING IC WITH P - Tape and Reel |
| ADE7755AN | 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述: |
| ADE7755AN-REF | 制造商:AD 制造商全称:Analog Devices 功能描述:Energy Metering IC with Pulse Output |
发布紧急采购，3分钟左右您将得到回复。