- 您现在的位置：买卖IC网 > PDF目录210168 > ADM1069AST-REEL7 (ANALOG DEVICES INC) 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP32 PDF资料下载
参数资料
| 型号： | ADM1069AST-REEL7 |
| 厂商： | ANALOG DEVICES INC |
| 元件分类： | 电源管理 |
| 英文描述： | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQFP32 |
| 封装： | MS-026-BBA, LQFP-32 |
| 文件页数： | 13/36页 |
| 文件大小： | 763K |
| 代理商： | ADM1069AST-REEL7 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
ADM1069
Rev. A | Page 20 of 36
Sequence Detector
The sequence detector block is used to detect when a step in a
sequence has been completed. It looks for one of the SE inputs
to change state, and is most often used as the gate on successful
progress through a power-up or power-down sequence. A timer
block is included in this detector, which can insert delays into a
power-up or power-down sequence, if required. Timer delays
can be set from 10 μs to 400 ms. Figure 27 is a block diagram of
the sequence detector.
04735-032
SUPPLY FAULT
DETECTION
LOGIC INPUT CHANGE
OR FAULT DETECTION
WARNINGS
FORCE FLOW
(UNCONDITIONAL JUMP)
VP1
VX4
INVERT
SEQUENCE
DETECTOR
SELECT
TIMER
Figure 27. Sequence Detector Block Diagram
The sequence detector can also help to identify monitoring
faults. In the sample application shown in Figure 26, the FSEL1
and FSEL2 states first identify which of the VP1,VP2, or VP3
pins has faulted, and then they take the appropriate action.
Monitoring Fault Detector
The monitoring fault detector block is used to detect a failure
on an input. The logical function implementing this is a wide
OR gate, which can detect when an input deviates from its
expected condition. The clearest demonstration of the use of
this block is in the PWRGD state, where the monitor block
indicates that a failure on one or more of the VP1,VP2, or VP3
inputs has occurred.
No programmable delay is available in this block because the
triggering of a fault condition is likely to be caused by a supply
falling out of tolerance. In this situation, the user needs to react as
quickly as possible. Some latency occurs when moving out of this
state, however, because it takes a finite amount of time (~20 μs) for
the state configuration to download from EEPROM into the SE.
Figure 28 is a block diagram of the monitoring fault detector.
04735-033
SUPPLY FAULT
DETECTION
LOGIC INPUT CHANGE
OR FAULT DETECTION
VP1
VX4
MONITORING FAULT
DETECTOR
MASK
SENSE
1-BIT FAULT
DETECTOR
FAULT
WARNINGS
MASK
1-BIT FAULT
DETECTOR
FAULT
MASK
SENSE
1-BIT FAULT
DETECTOR
FAULT
Figure 28. Monitoring Fault Detector Block Diagram
Timeout Detector
The timeout detector allows the user to trap a failure to make
proper progress through a power-up or power-down sequence.
In the sample application shown in Figure 26, the timeout next-
state transition is from the EN3V3 and EN2V5 states. For the
EN3V3 state, the signal 3V3ON is asserted upon entry to this
state (on the PDO1 output pin) to turn on a 3.3 V supply. This
supply rail is connected to the VP2 pin, and the sequence detec-
tor looks for the VP2 pin to go above its UV threshold, which is
set in the supply fault detector (SFD) attached to that pin.
The power-up sequence progresses when this change is
detected. If, however, the supply fails (perhaps due to a short
circuit overloading this supply), the timeout block traps the
problem. In this example, if the 3.3 V supply fails within 10 ms,
the SE moves to the DIS3V3 state and turns off this supply by
bringing PDO1 low. It also indicates that a fault has occurred by
taking PDO3 high. Timeout delays from 100 μs to 400 ms can
be programmed.
相关PDF资料 |
PDF描述 |
|---|---|
| AFL27005DX/CHPBF | 2-OUTPUT 66 W DC-DC REG PWR SUPPLY MODULE |
| AFL27012DX/CHPBF | 2-OUTPUT 66 W DC-DC REG PWR SUPPLY MODULE |
| APE2902Y5-46 | SWITCHING REGULATOR, PDSO5 |
| APE2902Y5R-49 | SWITCHING REGULATOR, PDSO5 |
| ATW2805S/-SLV | 1-OUTPUT 30 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1069ASTZ | 功能描述:IC SUPERVISOR/SEQUENCER 32-LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:Super Sequencer® 其它有关文件:STM6905 View All Specifications 标准包装:1 系列:- 类型:多压监控器 监视电压数目:5 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 140 ms 电压 - 阀值:2.188V，2.955V，可调，可调，可调 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-TSSOP 包装:Digi-Reel® 产品目录页面:1197 (CN2011-ZH PDF) 其它名称:497-8728-6 |
| ADM1069ASTZ-REEL | 功能描述:IC SEQUENCER/SUPERVISOR 32LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:Super Sequencer® 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| ADM1069ASTZ-REEL7 | 功能描述:IC SEQUENCER/SUPERVISOR 32LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:Super Sequencer® 其它有关文件:STM6905 View All Specifications 标准包装:1 系列:- 类型:多压监控器 监视电压数目:5 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 140 ms 电压 - 阀值:2.188V，2.955V，可调，可调，可调 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:8-TSSOP，8-MSOP（0.118"，3.00mm 宽） 供应商设备封装:8-TSSOP 包装:Digi-Reel® 产品目录页面:1197 (CN2011-ZH PDF) 其它名称:497-8728-6 |
| ADM1070 | 制造商:AD 制造商全称:Analog Devices 功能描述:-48 V Hot Swap Controller |
| ADM1070ART | 制造商:AD 制造商全称:Analog Devices 功能描述:-48 V Hot Swap Controller |
发布紧急采购，3分钟左右您将得到回复。