- 您现在的位置：买卖IC网 > PDF目录16832 > ADM1169ACPZ (Analog Devices Inc)IC SEQUENCER/SUPERVISOR 40LFCSP PDF资料下载
参数资料
| 型号： | ADM1169ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 26/36页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCER/SUPERVISOR 40LFCSP |
| 标准包装： | 1 |
| 系列： | Super Sequencer® |
| 应用： | 电源监控器，序列发生器 |
| 输入电压： | 3 V ~ 14.4 V |
| 电源电压： | 3 V ~ 14.4 V |
| 电流 - 电源： | 4.2mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 40-LFCSP-WQ（6x6） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页当前第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
ADM1169
COMMUNICATING WITH THE ADM1169
CONFIGURATION DOWNLOAD AT POWER-UP
The configuration of the ADM1169 (undervoltage/overvoltage
thresholds, glitch filter timeouts, and PDO configurations) is
dictated by the contents of the RAM. The RAM comprises
digital latches that are local to each of the functions on the device.
The latches are double-buffered and have two identical latches,
Latch A and Latch B. Therefore, when an update to a function
occurs, the contents of Latch A are updated first, and then the
contents of Latch B are updated with identical data. The advantages
Configuration section.
The two latches are volatile memory and lose their contents at
power-down. Therefore, the configuration in the RAM must be
restored at power-up by downloading the contents of the EEPROM
(nonvolatile memory) to the local latches. This download occurs
in steps, as follows:
Data Sheet
The ADM1169 provides several options that allow the user to
update the configuration over the SMBus interface. The following
three options are controlled in the UPDCFG register.
Option 1
Update the configuration in real time. The user writes to the RAM
across the SMBus, and the configuration is updated immediately.
Option 2
Update the Latch As without updating the Latch Bs. With this
method, the configuration of the ADM1169 remains unchanged
and continues to operate in the original setup until the instruction
is given to update the Latch Bs.
Option 3
Change the EEPROM register contents without changing the RAM
contents, and then download the revised EEPROM contents to the
RAM registers. With this method, the configuration of the
1.
2.
3.
4.
5.
6.
With no power applied to the device, the PDOs are all high
impedance.
When 1.2 V appears on any of the inputs connected to the
VDD arbitrator (VH or VPx), the PDOs are all weakly pulled
to GND with a 20 k? resistor.
When the supply rises above the undervoltage lockout of
the device (UVLO is 2.5 V), the EEPROM starts to
download to the RAM.
The EEPROM downloads its contents to all Latch As.
When the contents of the EEPROM are completely
downloaded to the Latch As, the device controller signals
all Latch As to download to all Latch Bs simultaneously,
completing the configuration download.
At 0.5 ms after the configuration download completes, the
first state definition is downloaded from the EEPROM
into the SE.
ADM1169 remains unchanged and continues to operate in the
original setup until the instruction is given to update the RAM.
section is also a useful way to restore the original EEPROM
contents if revisions to the configuration are unsatisfactory. For
example, if the user needs to alter an overvoltage threshold, the
section. However, if the user is not satisfied with the change and
wants to revert to the original programmed value, the device
controller can issue a command to download the EEPROM
section, restoring the ADM1169 to its original configuration.
The topology of the ADM1169 makes this type of operation
possible. The local, volatile registers (RAM) are all double-buffered
latches. Setting Bit 0 of the UPDCFG register to 1 leaves the
double buffered latches open at all times, allowing the registers
Note that any attempt to communicate with the device prior to
the completion of the download causes the ADM1169 to issue
a no acknowledge (NACK).
UPDATING THE CONFIGURATION
After power-up, with all the configuration settings loaded from
the EEPROM into the RAM registers, the user may need to alter
the configuration of functions on the ADM1169 , such as changing
the undervoltage or overvoltage limit of an SFD, changing the
fault output of an SFD, or adjusting the rise time delay of one
of the PDOs.
to be updated continuously as they are written to. If Bit 0 is set to
0 when a RAM write occurs across the SMBus, only the first side
of the double-buffered latch is written to. The user must then
write a 1 to Bit 1 of the UPDCFG register. This generates a pulse
to update all the second latches at once. EEPROM writes occur
in a similar way.
The final bit in this register can enable or disable EEPROM page
erasure. If this bit is set high, the contents of an EEPROM page can
all be set to 1. If this bit is set low, the contents of a page cannot be
erased, even if the command code for page erasure is programmed
across the SMBus. The bit map for the UPDCFG register is shown
in the AN-721 Application Note . A flow diagram for download at
power-up and subsequent configuration updates is shown in
Rev. A | Page 26 of 36
相关PDF资料 |
PDF描述 |
|---|---|
| SFSD-20-28-H-05.00-DR-NDX | CABLE ASSY SOCKET 40POS 28AWG |
| 207W234-25-01-0 | BOOT MOLDED |
| 382W042-25-0 | BOOT MOLDED |
| 382W042-3-0 | BOOT MOLDED |
| IS-DEV KIT-7D | KIT DEV FOR OLED DISPLAY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1169ACPZ-RL7 | 功能描述:IC SEQUENCER/SUPERVISOR 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1169ARTZ | 制造商:Analog Devices 功能描述:SUPER SEQUENCER W/ BLACK BOX - Tape and Reel |
| ADM1169ASTZ | 功能描述:IC SEQUENCER/SUPERVISOR 32LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1169ASTZ-RL7 | 功能描述:IC SEQUENCER/SUPERVISOR 32LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1170 | 制造商:AD 制造商全称:Analog Devices 功能描述:1.6 V to 16.5 V Hot Swap Controller with Soft Start |
发布紧急采购，3分钟左右您将得到回复。