- 您现在的位置：买卖IC网 > PDF目录16832 > ADM1169ACPZ (Analog Devices Inc)IC SEQUENCER/SUPERVISOR 40LFCSP PDF资料下载
参数资料
| 型号： | ADM1169ACPZ |
| 厂商： | Analog Devices Inc |
| 文件页数： | 27/36页 |
| 文件大小： | 0K |
| 描述： | IC SEQUENCER/SUPERVISOR 40LFCSP |
| 标准包装： | 1 |
| 系列： | Super Sequencer® |
| 应用： | 电源监控器，序列发生器 |
| 输入电压： | 3 V ~ 14.4 V |
| 电源电压： | 3 V ~ 14.4 V |
| 电流 - 电源： | 4.2mA |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-WFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 40-LFCSP-WQ（6x6） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
Data Sheet
POWER-UP
SMBus
DEVICE
ADM1169
(V CC > 2.5V)
E
CONTROLLER
R
U
E
P
R
O
M
L
D
D
A
T
A
LATCH A
A
M
L
D
P
D
LATCH B
FUNCTION
(OV THRESHOLD
EEPROM
Figure 35. Configuration Update Flow Diagram
ON VP1)
UPDATING THE SEQUENCING ENGINE
SE functions are not updated in the same way as regular
configuration latches. The SE has its own dedicated 512-byte
EEPROM for storing state definitions, providing 63 individual
states, each with a 64-bit word (one state is reserved). At power-up,
the first state is loaded from the SE EEPROM into the engine
itself. When the conditions of this state are met, the next state is
loaded from the EEPROM into the engine and so on. The loading
of each new state takes approximately 10 μs.
To alter a state, the required changes must be made directly to
the EEPROM. RAM for each state does not exist. The relevant
alterations must be made to the 64-bit word, which is then
uploaded directly to the EEPROM.
INTERNAL REGISTERS
The ADM1169 contains a large number of data registers. The
principal registers are the address pointer register and the
configuration registers.
Address Pointer Register
The address pointer register contains the address that selects one
the first byte of data is always a register address that is written to
the address pointer register.
Configuration Registers
The configuration registers provide control and configuration
for various operating parameters of the ADM1169 . See the
EEPROM
The ADM1169 has two 512-byte cells of nonvolatile, electrically
erasable, programmable read-only memory (EEPROM), from
Address 0xF800 to Register Address 0xFBFF. The EEPROM is
used for permanent storage of data that is not lost when the
ADM1169 is powered down. One EEPROM cell, 0xF800 to
0xF9FF, contains the configuration data, user information, and,
if enabled, any fault records of the device; the other section, 0xFA00
to 0xFBFF, contains the state definitions for the SE. Although
referred to as read-only memory, the EEPROM can be written to,
as well as read from, using the serial bus in exactly the same way
as the other registers.
The major differences between the EEPROM and other
registers are as follows:
? An EEPROM location must be blank before it can be
written to. If it contains data, the data must first be erased.
? Writing to the EEPROM is slower than writing to the RAM.
? Writing to the EEPROM should be restricted because it has
a limited write/cycle life of typically 10,000 write operations,
due to the usual EEPROM wear-out mechanisms.
The first EEPROM is split into 16 (0 to 15) pages of 32 bytes each.
Page 0 to Page 4, from Address 0xF800 to Address 0xF89F, hold
the configuration data for the applications on the ADM1169
(such as the SFDs and PDOs). These EEPROM addresses are
the same as the RAM register addresses, prefixed by F8. Page 5
to Page 7, from Address 0xF8A0 to Address 0xF8FF, are reserved.
Page 8 to Page 11 are available for customer use to store any
information that may be required by the customer in their
application. Customers can store information on Page 12 to
Page 15, or these pages can store the fault records written by the
sequencing engine if users have decided to enable writing of the
fault records for different states.
Data can be downloaded from the EEPROM to the RAM in one
of the following ways:
? At power-up, when Page 0 to Page 4 are downloaded.
? By setting Bit 0 of the UDOWNLD register (0xD8), which
performs a user download of Page 0 to Page 4.
When the sequence engine is enabled, it is not possible to access
the section of EEPROM from Address 0xFA00 to Address 0xFBFF.
The sequence engine must be halted before it is possible to read or
write to this range. Attempting to read or write to this range if the
sequence engine is not halted generates a no acknowledge,
or NACK.
Read/write access to the configuration and user EEPROM ranges
from Address 0xF800 to Address 0xF89F and Address 0xF900 to
Address 0xF9FF depends on whether the black box fault recorder is
enabled. If the fault recorder is enabled and one or more states
have been set as fault record trigger states, then it is not possible to
access any EEPROM location in this range without first halting
the black box. Attempts to read or write to this EEPROM range
while the fault recorder is operating are acknowledged by the
device but do not return any useful data or modify the EEPROM
in any way.
Rev. A | Page 27 of 36
相关PDF资料 |
PDF描述 |
|---|---|
| SFSD-20-28-H-05.00-DR-NDX | CABLE ASSY SOCKET 40POS 28AWG |
| 207W234-25-01-0 | BOOT MOLDED |
| 382W042-25-0 | BOOT MOLDED |
| 382W042-3-0 | BOOT MOLDED |
| IS-DEV KIT-7D | KIT DEV FOR OLED DISPLAY |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1169ACPZ-RL7 | 功能描述:IC SEQUENCER/SUPERVISOR 40LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1169ARTZ | 制造商:Analog Devices 功能描述:SUPER SEQUENCER W/ BLACK BOX - Tape and Reel |
| ADM1169ASTZ | 功能描述:IC SEQUENCER/SUPERVISOR 32LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1169ASTZ-RL7 | 功能描述:IC SEQUENCER/SUPERVISOR 32LQFP RoHS:是 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:Super Sequencer® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| ADM1170 | 制造商:AD 制造商全称:Analog Devices 功能描述:1.6 V to 16.5 V Hot Swap Controller with Soft Start |
发布紧急采购，3分钟左右您将得到回复。