- 您现在的位置：买卖IC网 > PDF目录19960 > ADM1176-2ARMZ-R7 (Analog Devices Inc)IC CTRLR HOTSWAP 16.5V 10-MSOP PDF资料下载
参数资料
| 型号： | ADM1176-2ARMZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 1/24页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR HOTSWAP 16.5V 10-MSOP |
| 产品培训模块： | Hot Swap Design |
| 标准包装： | 1 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 3.15 V ~ 16.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 标准包装 |
| 产品目录页面： | 792 (CN2011-ZH PDF) |
| 配用： | EVAL-ADM1176EBZ-ND - BOARD EVALUATION FOR ADM1176 |
| 其它名称： | ADM1176-2ARMZ-R7DKR |
Hot Swap Controller and
I 2 C Power Monitor
Data Sheet
FEATURES
FUNCTIONAL BLOCK DIAGRAM
Allows safe board insertion and removal from a live backplane
Controls supply voltages from 3.15 V to 16.5 V
Precision current sense amplifier
Precision voltage input
12-bit ADC for current and voltage readback
Charge-pumped gate drive for external N-channel FET
VCC
SENSE
ADM1176
A
V
I
MUX
0
1
12-BIT
ADC
I 2 C
SDA
SCL
A1
Adjustable analog current limit with circuit breaker
±3% accurate hot swap current limit level
Fast response limits peak fault current
CURRENT
SENSE
AMPLIFIER
A0
Automatic retry or latch-off on current fault
Programmable hot swap timing via TIMER pin
Active high ON pin
I 2 C fast mode-compliant interface (400 kHz maximum)
2 address pins allow 16 devices on the same bus
ON
1.3V
UNDERVOLTAGE
COMPARATOR
GND
FET DRIVE
CONTROLLER
TIMER
GATE
10-lead MSOP
APPLICATIONS
Figure 1.
Power monitoring/power budgeting
3.15V TO 16.5V
R SENSE
N-CHANNEL FET
Central office equipment
Telecommunications and data communications equipment
PCs/servers
VCC
SENSE
CONTROLLER
GENERAL DESCRIPTION
GATE
ADM1176
P = VI
The ADM1176 is an integrated hot swap controller that offers
digital current and voltage monitoring via an on-chip 12-bit
ON
SDA
SCL
SDA
SCL
analog-to-digital converter (ADC), communicated through an
I 2 C? interface.
TIMER
GND
A1
A0
An internal current sense amplifier measures voltage across the
sense resistor in the power path via the VCC pin and the SENSE pin.
The ADM1176 limits the current through this resistor by control-
ling the gate voltage (via the GATE pin) of an external N-
channel FET in the power path. The voltage across the sense
resistor (and therefore the inrush current) is kept below a preset
maximum.
The ADM1176 protects the external FET by limiting the time that
the maximum current runs through it. This current limit period
is set by the value of the capacitor attached to the TIMER pin.
Additionally, the device provides protection from overcurrent
events that may occur after the hot swap event is complete. In
the case of a short-circuit event, the current in the sense resistor
exceeds an overcurrent trip threshold, and the FET is switched
off immediately by pulling down the GATE pin.
Rev. C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
Figure 2. Applications Diagram
A 12-bit ADC can measure the current seen in the sense
resistor, as well as the supply voltage on the VCC pin. An
industry-standard I 2 C interface allows a controller to read
current and voltage data from the ADC. Measurements can be
initiated by an I 2 C command. Alternatively, the ADC can run
continuously, and the user can read the latest conversion data
whenever it is required. Up to 16 unique I 2 C addresses can be
created, depending on how the A0 and A1 pins are connected.
The ADM1176 is packaged in a 10-lead MSOP.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 ?2006–2012 Analog Devices, Inc. All rights reserved.
相关PDF资料 |
PDF描述 |
|---|---|
| TLJN106M010R2500 | CAP TANT 10UF 10V 20% 0805 |
| T86C684M050EBAS | CAP TANT 0.68UF 50V 20% 2312 |
| MMBD1501A_D87Z | DIODE 200V 200MA SOT23 |
| VI-JWZ-CY-B1 | CONVERTER MOD DC/DC 2V 20W |
| UM-3NPAL3X2 | BATT PK 9.0V AA SIZE CARBON ZINC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1176EBZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Hot Swap Controller and I2C㈢ Power Monitor with Convert Pin |
| ADM1177 | 制造商:AD 制造商全称:Analog Devices 功能描述:Hot Swap Controller and Digital Power Monitor with Soft-Start Pin |
| ADM1177-1ARMZ-R7 | 功能描述:IC CTRLR HOTSWAP 16.5V 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1177-2ARMZ-R7 | 功能描述:IC CTRLR HOTSWAP 16.5V 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1178 | 制造商:AD 制造商全称:Analog Devices 功能描述:Hot Swap Controller and Digital Power Monitor with AlertB Output |
发布紧急采购，3分钟左右您将得到回复。