- 您现在的位置：买卖IC网 > PDF目录19960 > ADM1176-2ARMZ-R7 (Analog Devices Inc)IC CTRLR HOTSWAP 16.5V 10-MSOP PDF资料下载
参数资料
| 型号： | ADM1176-2ARMZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/24页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR HOTSWAP 16.5V 10-MSOP |
| 产品培训模块： | Hot Swap Design |
| 标准包装： | 1 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 3.15 V ~ 16.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 标准包装 |
| 产品目录页面： | 792 (CN2011-ZH PDF) |
| 配用： | EVAL-ADM1176EBZ-ND - BOARD EVALUATION FOR ADM1176 |
| 其它名称： | ADM1176-2ARMZ-R7DKR |
ADM1176
GATE AND TIMER FUNCTIONS DURING
A HOT SWAP OPERATION
During hot insertion of a board onto a live supply rail at VCC,
the abrupt application of supply voltage charges the external
FET drain/gate capacitance, which can cause an unwanted gate
Data Sheet
CALCULATING CURRENT LIMITS AND FAULT
CURRENT LIMIT TIME
The nominal linear current limit is determined by a sense
resistor connected between the VCC pin and the SENSE pin
as given by Equation 1.
voltage spike. An internal circuit holds GATE low before the
internal circuitry wakes up. This substantially reduces the FET
current surges at insertion. The GATE pin is also held low
during the initial timing cycle until the ON pin is taken high to
start the hot swap operation.
During a hot swap operation, the GATE pin is first pulled up by
a 12.5 μA current source. If the current through the sense resistor
reaches the overcurrent fault timing threshold (V OCTRIM ), a pull-
up current of 60 μA on the TIMER pin is turned on and the
GATE pin starts charging up. At a slightly higher voltage in the
sense resistor, the error amplifier servos the GATE pin to maintain
I LIMIT(NOM) = V LIM(NOM) / R SENSE = 100 mV/ R SENSE
The minimum linear fault current is given by Equation 2.
I LIMIT(MIN) = V LIM(MIN) / R SENSE(MAX) = 97 mV/ R SENSE(MAX)
The maximum linear fault current is given by Equation 3.
I LIMIT(MAX) = V LIM(MAX) / R SENSE(MIN) = 103 mV/ R SENSE(MIN)
The power rating of the sense resistor should be rated at the
maximum linear fault current level.
The minimum overcurrent fault timing threshold current is
given by Equation 4.
(1)
(2)
(3)
a constant current to the load by controlling the voltage across
the sense resistor to the linear current limit, V LIM .
A normal hot swap operation is complete when the board supply
capacitors near full charge and the current through the sense
resistor drops to eventually reach the level of the board load
current. As soon as the current drops below the overcurrent
fault timing threshold, the current into the TIMER pin switches
from being a 60 μA pull-up to being a 100 μA pull-down. The
ADM1176 then drives the GATE voltage as high as it can to
fully enhance the FET and reduce R ON losses to a minimum.
A hot swap operation fails if the load current does not drop
below the overcurrent fault timing threshold, V OCTRIM , before the
TIMER pin has charged up to 1.3 V. In this case, the GATE pin
is then pulled down with a 1.5 mA to 7 mA current sink (this varies
with supply voltage). The GATE pull-down stays on until a hot
swap retry starts, which can be forced by deasserting and then
reasserting the ON pin. On the ADM1176-1, the device retries a
hot swap operation automatically after a cooldown period.
The ADM1176 also features a method of protection from
sudden load current surges, such as a low impedance fault,
when the current seen across the sense resistor may go well
beyond the linear current limit. If the fast overcurrent trip
threshold, V OCFAST , is exceeded, the 1.5 mA to 7 mA GATE pull-
down is turned on immediately. This pulls the GATE voltage
down quickly to enable the ADM1176 to limit the length of the
current spike that passes through the external FET and to bring
I OCTRIM(MIN) = V OCTRIM(MIN) / R SENSE(MAX) = 90 mV/ R SENSE(MAX) (4)
The maximum fast overcurrent trip threshold current is given
by Equation 5.
I OCFAST(MAX) = V OCFAST(MAX) / R SENSE(MIN) = 115 mV/ R SENSE(MIN) (5)
The fault current limit time is the time that a device spends
timing an overcurrent fault. The fault current limit time is given
by Equation 6.
t FAULT ≈ 21.7 × C TIMER ms/μF (6)
INITIAL TIMING CYCLE
When VCC is first connected to the backplane supply, the
internal supply (Time Point 1 in Figure 30) of the ADM1176
must be charged up. A very short time later (significantly less
than 1 ms), the internal supply is fully up and, because the
undervoltage lockout voltage is exceeded at VCC, the device
comes out of reset. During this first short reset period, the
GATE pin is held down with a 25 mA pull-down current, and
the TIMER pin is pulled down with a 100 μA current sink.
The ADM1176 then goes through an initial timing cycle. At
Time Point 2, the TIMER pin is pulled high with 5 μA. At Time
Point 3, the TIMER reaches the V TIMERL threshold, and the first
portion of the initial cycle ends. The 100 μA current source then
pulls down the TIMER pin until it reaches 0.2 V at Time Point 4.
The initial cycle delay (Time Point 2 to Time Point 4) is related
to C TIMER as shown in Equation 7.
the current through the sense resistor back into linear regulation as
quickly as possible. This process protects the backplane supply
from sustained overcurrent conditions that can otherwise cause
the backplane supply to droop during the overcurrent event.
Rev. C | Page 14 of 24
t INITIAL ≈ 270 × C TIMER ms/μF
(7)
相关PDF资料 |
PDF描述 |
|---|---|
| TLJN106M010R2500 | CAP TANT 10UF 10V 20% 0805 |
| T86C684M050EBAS | CAP TANT 0.68UF 50V 20% 2312 |
| MMBD1501A_D87Z | DIODE 200V 200MA SOT23 |
| VI-JWZ-CY-B1 | CONVERTER MOD DC/DC 2V 20W |
| UM-3NPAL3X2 | BATT PK 9.0V AA SIZE CARBON ZINC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1176EBZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Hot Swap Controller and I2C㈢ Power Monitor with Convert Pin |
| ADM1177 | 制造商:AD 制造商全称:Analog Devices 功能描述:Hot Swap Controller and Digital Power Monitor with Soft-Start Pin |
| ADM1177-1ARMZ-R7 | 功能描述:IC CTRLR HOTSWAP 16.5V 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1177-2ARMZ-R7 | 功能描述:IC CTRLR HOTSWAP 16.5V 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1178 | 制造商:AD 制造商全称:Analog Devices 功能描述:Hot Swap Controller and Digital Power Monitor with AlertB Output |
发布紧急采购，3分钟左右您将得到回复。