- 您现在的位置：买卖IC网 > PDF目录19960 > ADM1176-2ARMZ-R7 (Analog Devices Inc)IC CTRLR HOTSWAP 16.5V 10-MSOP PDF资料下载
参数资料
| 型号： | ADM1176-2ARMZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 19/24页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR HOTSWAP 16.5V 10-MSOP |
| 产品培训模块： | Hot Swap Design |
| 标准包装： | 1 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 3.15 V ~ 16.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 标准包装 |
| 产品目录页面： | 792 (CN2011-ZH PDF) |
| 配用： | EVAL-ADM1176EBZ-ND - BOARD EVALUATION FOR ADM1176 |
| 其它名称： | ADM1176-2ARMZ-R7DKR |
Data Sheet
WRITE EXTENDED COMMAND BYTE
ADM1176
In the write extended command byte operation, the master
device writes to one of the three extended registers of the slave
device, as follows:
7.
8.
The slave asserts an acknowledge on SDA.
The master asserts a stop condition on SDA to end
the transaction.
1.
The master device asserts a start condition on SDA.
1
2
3
4
5
6
7 8
SLAVE
REGISTER
2.
3.
4.
The master sends the 7-bit slave address, followed by the
write bit (low).
The addressed slave device asserts an acknowledge on SDA.
The master sends the register address byte. The MSB of
this byte is set to 1 to indicate an extended register write.
The two LSBs indicate which of the three extended
EXTENDED
S ADDRESS W A ADDRESS A COMMAND A P
BYTE
Figure 37. Write Extended Byte
extended register.
5.
6.
registers is to be written to (see Table 8). All other bits
should be set to 0.
The slave asserts an acknowledge on SDA.
The master sends the extended command byte (refer to
Table 8. Extended Register Addresses
A6 A5 A4 A3 A2 A1 A0
0 0 0 0 0 0 1
0 0 0 0 0 1 0
0 0 0 0 0 1 1
Extended Register
ALERT_EN
ALERT_TH
CONTROL
Table 9. ALERT_EN Register Operations
Bit
0
1
Default
0
0
Name
EN_ADC_OC1
EN_ADC_OC4
Function
LSB, enabled if a single ADC conversion on the I channel exceeds the threshold set in the ALERT_TH register.
Enabled if four consecutive ADC conversions on the I channel exceed the threshold set in the
ALERT_TH register.
2
1
EN_HS_ALERT
Enabled if the hot swap operation either has latches off or enters a cooldown cycle because of an
overcurrent event.
3
0
EN_OFF_ALERT
Enables an alert if the hot swap operation is turned off by a transition that deasserts the ON pin or by an
operation that writes the SWOFF bit high.
4
0
CLEAR
Clears the OFF_ALERT, HS_ALERT, and ADC_ALERT status bits in the STATUS register. The value of these
bits may immediately change if the source of the alert is not cleared and the alert function is not disabled.
The CLEAR bit self-clears to 0 after the STATUS register bits are cleared.
Table 10. ALERT_TH Register Operations
Bit
[7:0]
Default
FF
Function
The ALERT_TH register sets the current level at which an alert occurs. Defaults to ADC full scale. The ALERT_TH 8-bit value
corresponds to the top eight bits of the current channel data.
Table 11. CONTROL Register Operations
Bit
0
Default
0
Name
SWOFF
Function
LSB, forces the hot swap operation off. Equivalent to deasserting the ON pin.
Rev. C | Page 19 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| TLJN106M010R2500 | CAP TANT 10UF 10V 20% 0805 |
| T86C684M050EBAS | CAP TANT 0.68UF 50V 20% 2312 |
| MMBD1501A_D87Z | DIODE 200V 200MA SOT23 |
| VI-JWZ-CY-B1 | CONVERTER MOD DC/DC 2V 20W |
| UM-3NPAL3X2 | BATT PK 9.0V AA SIZE CARBON ZINC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1176EBZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Hot Swap Controller and I2C㈢ Power Monitor with Convert Pin |
| ADM1177 | 制造商:AD 制造商全称:Analog Devices 功能描述:Hot Swap Controller and Digital Power Monitor with Soft-Start Pin |
| ADM1177-1ARMZ-R7 | 功能描述:IC CTRLR HOTSWAP 16.5V 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1177-2ARMZ-R7 | 功能描述:IC CTRLR HOTSWAP 16.5V 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1178 | 制造商:AD 制造商全称:Analog Devices 功能描述:Hot Swap Controller and Digital Power Monitor with AlertB Output |
发布紧急采购，3分钟左右您将得到回复。