- 您现在的位置：买卖IC网 > PDF目录19960 > ADM1176-2ARMZ-R7 (Analog Devices Inc)IC CTRLR HOTSWAP 16.5V 10-MSOP PDF资料下载
参数资料
| 型号： | ADM1176-2ARMZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 16/24页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR HOTSWAP 16.5V 10-MSOP |
| 产品培训模块： | Hot Swap Design |
| 标准包装： | 1 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 3.15 V ~ 16.5 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 10-TFSOP，10-MSOP（0.118"，3.00mm 宽） |
| 供应商设备封装： | 10-MSOP |
| 包装： | 标准包装 |
| 产品目录页面： | 792 (CN2011-ZH PDF) |
| 配用： | EVAL-ADM1176EBZ-ND - BOARD EVALUATION FOR ADM1176 |
| 其它名称： | ADM1176-2ARMZ-R7DKR |
ADM1176
VOLTAGE AND CURRENT READBACK
In addition to providing hot swap functionality, the ADM1176
contains the components to allow voltage and current readback
over an I 2 C bus. The voltage output of the current sense amplifier
and the voltage on the VCC pin are fed into a 12-bit ADC via a
multiplexer. The device can be instructed to convert voltage
and/or current at any time during operation via an I 2 C command.
When all conversions are complete, the voltage and/or current
values can be read back with 12-bit accuracy in two or three bytes.
SERIAL BUS INTERFACE
Data Sheet
The peripheral whose address corresponds to the transmitted
address responds by pulling the data line low during the
low period before the ninth clock pulse, known as the
acknowledge bit, and holding it low during the high period of
this clock pulse. All other devices on the bus now remain
idle while the selected device waits for data to be read from
it or written to it. If the R/W bit is 0, the master writes to the
slave device. If the R/W bit is 1, the master reads from the
slave device.
Control of the ADM1176 is carried out via the I 2 C bus. This
interface is compatible with the fast mode I 2 C (400 kHz
maximum). The ADM1176 is connected to this bus as a slave
device under the control of a master device.
IDENTIFYING THE ADM1176 ON THE I 2 C BUS
The ADM1176 has a 7-bit serial bus slave address. When the
device powers up, it does so with a default serial bus address.
The three MSBs of the address are set to 100, and the four LSBs
are determined by the state of the A0 pin and the A1 pin. There
are 16 configurations available on the A0 pin and the A1 pin that
This scheme allows 16 ADM1176 devices to operate on a single
I 2 C bus.
GENERAL I 2 C TIMING
and read operations using the I 2 C. The I 2 C specification defines
conditions for different types of read and write operations, which
are discussed in the Write and Read Operations section. The
general I 2 C protocol operates as follows:
1. The master initiates a data transfer by establishing a start
condition, defined as a high-to-low transition on the serial
data line, SDA, while the serial clock line, SCL, remains high.
This indicates that a data stream is to follow. All slave periph-
erals connected to the serial bus respond to the start condition
and shift in the next eight bits, consisting of a 7-bit slave
address (MSB first) plus an R/W bit that determines the
direction of the data transfer, that is, whether data is to be
written to or read from the slave device (0 = write, 1 = read).
Table 5. Setting I 2 C Addresses via t he A0 Pin and the A 1 Pin
2.
3.
Data is sent over the serial bus in sequences of nine clock
pulses: eight bits of data followed by an acknowledge bit
from the slave device. Data transitions on the data line
must occur during the low period of the clock signal and
remain stable during the high period because a low-to-
high transition when the clock is high can be interpreted as
a stop signal.
If the operation is a write operation, the first data byte after
the slave address is a command byte. This tells the slave device
what to expect next. It can be an instruction, such as telling
the slave device to expect a block write, or it can be a register
address that tells the slave where subsequent data is to be
written.
Because data can flow in only one direction, as defined by
the R/W bit, it is not possible to send a command to a slave
device during a read operation. Before performing a read
operation, it may be necessary to first execute a write
operation to tell the slave what sort of read operation to
expect and/or the address from which data is to be read.
When all data bytes are read or written, stop conditions are
established. In write mode, the master pulls the data line
high during the 10 th clock pulse to assert a stop condition.
In read mode, the master device releases the SDA line
during the SCL low period before the ninth clock pulse,
but the slave device does not pull it low. This is known as a
no acknowledge. The master then takes the data line low
during the SCL low period before the 10 th clock pulse and
then high during the 10 th clock pulse to assert a stop condition.
Base Address
100
A1 Pin State
Ground
Ground
Ground
Ground
Resistor to ground
Resistor to ground
Resistor to ground
Resistor to ground
Floating
Floating
Floating
A0 Pin State
Ground
Resistor to ground
Floating
High
Ground
Resistor to ground
Floating
High
Ground
Resistor to ground
Floating
A1 Pin Logic State
00
00
00
00
01
01
01
01
10
10
10
A0 Pin Logic State
00
01
10
11
00
01
10
11
00
01
10
Address in Binary 1
1000000X
1000001X
1000010X
1000011X
1000100X
1000101X
1000110X
1000111X
1001000X
1001001X
1001010X
Address in Hex
0x80
0x82
0x84
0x86
0x88
0x8A
0x8C
0x8E
0x90
0x92
0x94
Rev. C | Page 16 of 24
相关PDF资料 |
PDF描述 |
|---|---|
| TLJN106M010R2500 | CAP TANT 10UF 10V 20% 0805 |
| T86C684M050EBAS | CAP TANT 0.68UF 50V 20% 2312 |
| MMBD1501A_D87Z | DIODE 200V 200MA SOT23 |
| VI-JWZ-CY-B1 | CONVERTER MOD DC/DC 2V 20W |
| UM-3NPAL3X2 | BATT PK 9.0V AA SIZE CARBON ZINC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADM1176EBZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Hot Swap Controller and I2C㈢ Power Monitor with Convert Pin |
| ADM1177 | 制造商:AD 制造商全称:Analog Devices 功能描述:Hot Swap Controller and Digital Power Monitor with Soft-Start Pin |
| ADM1177-1ARMZ-R7 | 功能描述:IC CTRLR HOTSWAP 16.5V 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1177-2ARMZ-R7 | 功能描述:IC CTRLR HOTSWAP 16.5V 10-MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 标准包装:50 系列:- 类型:热交换控制器 应用:-48V 远程电力系统，AdvancedTCA ? 系统，高可用性 内部开关:无 电流限制:可调 电源电压:11.5 V ~ 14.5 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| ADM1178 | 制造商:AD 制造商全称:Analog Devices 功能描述:Hot Swap Controller and Digital Power Monitor with AlertB Output |
发布紧急采购，3分钟左右您将得到回复。