- 您现在的位置：买卖IC网 > PDF目录9663 > ADN2804ACPZ-RL7 (Analog Devices Inc)IC CLK/DATA REC 622MBPS 32-LFCSP PDF资料下载
参数资料
| 型号： | ADN2804ACPZ-RL7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 10/24页 |
| 文件大小： | 0K |
| 描述： | IC CLK/DATA REC 622MBPS 32-LFCSP |
| 标准包装： | 1,500 |
| 类型： | 时钟和数据恢复（CDR），多路复用器 |
| PLL： | 是 |
| 主要目的： | SONET/SDH |
| 输入： | CML |
| 输出： | LVDS |
| 电路数： | 1 |
| 比率 - 输入:输出： | 1:2 |
| 差分 - 输入:输出： | 是/是 |
| 频率 - 最大： | 622MHz |
| 电源电压： | 3 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 32-LFCSP-VQ（5x5） |
| 包装： | 带卷 (TR) |
ADN2804
Data Sheet
Rev. C | Page 18 of 24
To control the device on the bus, the following protocol must be
followed. First, the master initiates a data transfer by establish-
ing a start condition, defined by a high-to-low transition on
SDA while SCK remains high. This indicates that an address/
data stream follows. All peripherals respond to the start condition
and shift the next eight bits (the 7-bit address and the R/W bit).
The bits are transferred from MSB to LSB. The peripheral that
recognizes the transmitted address responds by pulling the data
line low during the ninth clock pulse. This is known as an
acknowledge bit. All other devices withdraw from the bus at
this point and maintain an idle condition. The idle condition is
where the device monitors the SDA and SCK lines, waiting for
the start condition and correct transmitted address. The R/W
bit determines the direction of the data. Logic 0 on the LSB of
the first byte means that the master writes information to the
peripheral. Logic 1 on the LSB of the first byte means that the
master reads information from the peripheral.
The ADN2804 acts as a standard slave device on the bus. The data
on the SDA pin is eight bits long, supporting the 7-bit addresses
plus the R/W bit. The ADN2804 has eight subaddresses to enable
the user-accessible internal registers (see Table 6 through
Table 10). It, therefore, interprets the first byte as the device
address and the second byte as the starting subaddress. Auto-
increment mode is supported, allowing data to be read from or
written to the starting subaddress and each subsequent address
without manually addressing the subsequent subaddress. A data
transfer is always terminated by a stop condition. The user can
also access any unique subaddress register on a one-by-one
basis without updating all registers.
Stop and start conditions can be detected at any stage of the
data transfer. If these conditions are asserted out of sequence
with normal read and write operations, they cause an immediate
jump to the idle condition. During a given SCK high period, the
user should issue one start condition, one stop condition, or a
single stop condition followed by a single start condition. If an
invalid subaddress is issued by the user, the ADN2804 does not
issue an acknowledge and returns to the idle condition. If the
user exceeds the highest subaddress while reading back in auto-
increment mode, then the highest subaddress register contents
continue to be output until the master device issues a no acknow-
ledge. This indicates the end of a read. In a no-acknowledge
condition, the SDATA line is not pulled low on the ninth pulse.
and Figure 10 for a more detailed timing diagram.
Additional Features Available via the I2C Interface
LOS Configuration
The LOS detector output, Pin 22, can be configured to be either
active high or active low. If CTRLC[2] is set to Logic 0 (default),
the LOS pin is active high when a loss-of-signal condition is
detected. Writing a 1 to CTRLC[2] configures the LOS pin to be
active low when a loss-of-signal condition is detected.
System Reset
A frequency acquisition can be initiated by writing a 1 followed
by a 0 to the I2C Register Bit CTRLB[5]. This initiates a new
frequency acquisition while keeping the ADN2804 in its
previously programmed operating mode, as set in Registers
CTRL[A], CTRL[B], and CTRL[C].
相关PDF资料 |
PDF描述 |
|---|---|
| MS3120F22-55P | CONN RCPT 55POS WALL MNT W/PINS |
| MS27497E24B2PA | CONN RCPT 100POS WALL MNT W/PINS |
| AD9523BCPZ-REEL7 | IC INTEGER-N CLCK GEN 72LFCSP |
| PT06A-20-16P | CONN PLUG 16 POS STRAIGHT W/PINS |
| VE-JTW-MX-F3 | CONVERTER MOD DC/DC 5.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADN2805 | 制造商:AD 制造商全称:Analog Devices 功能描述:1.25 Gbps Clock and Data Recovery IC |
| ADN2805ACPZ | 功能描述:IC CLK/DATA REC 1.25GBPS 32LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:- 标准包装:1 系列:- 类型:时钟/频率发生器，多路复用器 PLL:是 主要目的:存储器，RDRAM 输入:晶体 输出:LVCMOS 电路数:1 比率 - 输入:输出:1:2 差分 - 输入:输出:无/是 频率 - 最大:400MHz 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:16-TSSOP 包装:Digi-Reel® 其它名称:296-6719-6 |
| ADN2805ACPZ-500RL7 | 功能描述:IC CLK/DATA REC 1.25GBPS 32LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:- 标准包装:28 系列:- 类型:时钟/频率发生器 PLL:是 主要目的:Intel CPU 服务器 输入:时钟 输出:LVCMOS 电路数:1 比率 - 输入:输出:3:22 差分 - 输入:输出:无/是 频率 - 最大:400MHz 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 85°C 安装类型:表面贴装 封装/外壳:64-TFSOP （0.240"，6.10mm 宽） 供应商设备封装:64-TSSOP 包装:管件 |
| ADN2805ACPZ-RL7 | 功能描述:IC CLK/DATA REC 1.25GBPS 32LFCSP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 专用 系列:- 标准包装:28 系列:- 类型:时钟/频率发生器 PLL:是 主要目的:Intel CPU 服务器 输入:时钟 输出:LVCMOS 电路数:1 比率 - 输入:输出:3:22 差分 - 输入:输出:无/是 频率 - 最大:400MHz 电源电压:3.135 V ~ 3.465 V 工作温度:0°C ~ 85°C 安装类型:表面贴装 封装/外壳:64-TFSOP （0.240"，6.10mm 宽） 供应商设备封装:64-TSSOP 包装:管件 |
| ADN2806 | 制造商:AD 制造商全称:Analog Devices 功能描述:622 Mbps Clock and Data Recovery IC |
发布紧急采购，3分钟左右您将得到回复。