- 您现在的位置：买卖IC网 > PDF目录1777 > ADP3207CJCPZ-RL (ON Semiconductor)IC CTLR SYNC BUCK 7BIT 40-LFCSP PDF资料下载
参数资料
| 型号： | ADP3207CJCPZ-RL |
| 厂商： | ON Semiconductor |
| 文件页数： | 23/32页 |
| 文件大小： | 0K |
| 描述： | IC CTLR SYNC BUCK 7BIT 40-LFCSP |
| 标准包装： | 2,500 |
| 应用： | 控制器，Intel IMVP-6 |
| 输入电压： | 3.3 V ~ 22 V |
| 输出数： | 3 |
| 输出电压： | 0.3 V ~ 1.5 V |
| 工作温度： | -10°C ~ 100°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 40-VFQFN 裸露焊盘，CSP |
| 供应商设备封装： | 40-LFCSP-VQ（6x6） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
ADP3207C
R T + * 5 k W
I R +
f SW
Application Information
The design parameters for a typical Intel IMVP6 ? compliant
CPU core VR application are as follows:
? Maximum input voltage (V INMAX ) = 19 V
? Minimum input voltage (V INMIN ) = 7.0 V
? Output voltage by VID setting (V VID ) = 1.150 V
? Maximum output current (I O ) = 44 A
? Load line slope (R O ) = 2.1 m W
? Maximum output current step ( D I O ) = 34.5 A
? Maximum output thermal current (I OTDC ) = 32 A
? Number of phases (n) = 2
? Switching frequency per phase (f SW ) = 280 kHz
? Duty cycle at maximum input voltage (D MIN ) = 0.061
? Duty cycle at minimum input voltage (D MAX ) = 0.164
Setting the Clock Frequency for PWM Mode
In PWM mode operation, the ADP3207C uses a
fixed ? frequency control architecture. The frequency is set
by an external timing resistor (R T ). The clock frequency and
the number of phases determine the switching frequency per
phase, which directly relates to switching losses and the
sizes of the inductors and input and output capacitors. In a
2 ? phase design, a clock frequency of 560 kHz sets the
switching frequency to 280 kHz per phase. This selection
represents a trade ? off between the switching losses and the
minimum sizes of the output filter components. To achieve
a 560 kHz oscillator frequency at VID voltage 1.150 V, R T
has to be 237 k W . Alternatively, the value for R T can be
calculated using:
V VID ) 1.0 V
n f SW 16 pF (eq. 1)
where 16 pF and 5 k W are internal IC component values. For
good initial accuracy and frequency stability, it is
recommended to use a 1% resistor.
Current Monitor Output
The I MON pin output a current proportional to the inductor
current.
Inductor Selection
The choice of inductance determines the ripple current in
the inductor. Less inductance leads to more ripple current,
which increases the output ripple voltage and conduction
losses in the MOSFETs. However, this allows the use of
smaller size inductors, and for a specified peak ? to ? peak
transient deviation, it allows less total output capacitance.
Conversely, a higher inductance means lower ripple current
and reduced conduction losses but requires larger size
inductors and more output capacitance for the same
peak ? to ? peak transient deviation. In a multi ? phase converter,
the practical peak ? to ? peak inductor ripple current is less than
50% of the maximum dc current in the same inductor.
Equation 2 shows the relationship between the inductance,
oscillator frequency, and peak ? to ? peak ripple current.
Equation 3 can be used to determine the minimum inductance
based on a given output ripple voltage.
V VID 1 * D MIN
L (eq. 2)
V VID R O (1 * (n D MIN)) (1 * D MIN )
L w
f SW V RIPPLE (eq. 3)
Solving Equation 3 for a 20 mV peak ? to ? peak output ripple
voltage yields:
1.150 V 2.1 m W (1 * (2 0.061)) (1 * 0.061)
L w
280 kHz 20 mV
+ 356 nH (eq. 4)
If the ripple voltage ends up being less than the initially
selected value, then the inductor can be changed to a smaller
value until the ripple value is met. This iteration allows
optimal transient response and minimum output decoupling.
The smallest possible inductor should be used to minimize
the number of output capacitors. For this example, choosing
a 360 nH inductor is a good starting point and gives a
calculated ripple current of 10.7 A. The inductor should not
saturate at the peak current of 27.4 A and should be able to
handle the sum of the power dissipation caused by the
average current of 16 A in the winding and core loss.
Another important factor in the inductor design is the
DCR, which is used to measure phase currents. A large DCR
causes excessive power losses, though too small a value
leads to increased measurement error. This example uses an
inductor with a DCR of 0.89 m W .
Selecting a Standard Inductor
Once the inductance and DCR are known, the next step is
to either design an inductor or select a standard inductor that
comes as close as possible to meeting the overall design goals.
It is also important to have the inductance and DCR tolerance
specified to keep the accuracy of the system controlled; 20%
inductance and 15% DCR (at room temperature) are
reasonable expectations that most manufacturers can meet.
Power Inductor Manufacturers
The following companies provide surface mount power
inductors optimized for high power applications upon
request:
? Vishay Dale Electronics, Inc.
? Panasonic
? Sumida Corporation
? NEC Tokin Corporation
Output Droop Resistance
The inductor design requires that the regulator output
voltage measured at the CPU pins drops when the output
current increases. The specified voltage drop corresponds to
a dc output resistance (R O ).
The output current is measured by summing the currents of
the resistors monitoring the voltage across each inductor and
http://onsemi.com
23
相关PDF资料 |
PDF描述 |
|---|---|
| ADP3207DJCPZ-RL | IC CTLR BUCK 7BIT MULTI 40LFCSP |
| ADP3208CJCPZ-RL | IC CTLR BUCK 7BIT IMVP6 48LFCSP |
| ADP3208DJCPZ-RL | IC CTLR BUCK 7BIT 2PHASE 48LFCSP |
| ADP320ACPZ-110-R7 | IC REG LDO 3.3/3.3/1.5V 16LFCSP |
| ADP3210MNR2G | IC CTLR BUCK 7BIT MULTIPH 40QFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP3207D | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:7-Bit Programmable, Multi-Phase Mobile, CPU Synchronous Buck |
| ADP3207DJCPZ-RL | 功能描述:DC/DC 开关控制器 IMVP6 BUCK CONTROLLER RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| ADP3207JCPZ-RL | 功能描述:DC/DC 开关控制器 IMVP6 MLTI/PHSE CNTR RoHS:否 制造商:Texas Instruments 输入电压:6 V to 100 V 开关频率: 输出电压:1.215 V to 80 V 输出电流:3.5 A 输出端数量:1 最大工作温度:+ 125 C 安装风格: 封装 / 箱体:CPAK |
| ADP3208AJCPZ-RL | 功能描述:肖特基二极管与整流器 IMVP6 MLT-PH CTRL W/DRVR RoHS:否 制造商:Skyworks Solutions, Inc. 产品:Schottky Diodes 峰值反向电压:2 V 正向连续电流:50 mA 最大浪涌电流: 配置:Crossover Quad 恢复时间: 正向电压下降:370 mV 最大反向漏泄电流: 最大功率耗散:75 mW 工作温度范围:- 65 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SOT-143 封装:Reel |
| ADP3208C | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:7-Bit,Programmable,Dual- Phase,Mobile,CPU,Synchronous Buck Controller |
发布紧急采购，3分钟左右您将得到回复。