- 您现在的位置：买卖IC网 > Datasheet目录308 > ADP8863ACPZ-R7 (Analog Devices Inc)IC LED DRVR WHIT BCKLGT 20-WLCSP Datasheet资料下载
参数资料
| 型号： | ADP8863ACPZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 14/52页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHIT BCKLGT 20-WLCSP |
| 标准包装： | 1 |
| 拓扑： | 切换式电容器（充电泵） |
| 输出数： | 7 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，LED 闪烁器 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 800kHz ~ 1.32MHz |
| 电源电压： | 2.5 V ~ 5.5 V |
| 输出电压： | 4.3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-UFBGA，WLCSP |
| 供应商设备封装： | 20-WLCSP |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | ADP8863ACPZ-R7DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
ADP8863
LED GROUPINGS
Each LED can respond individually or be grouped together
into the backlight controls. By default, all LEDs are set to be
part of the backlight. This is changed by setting Bits[6:0] in
Register 0x05. LEDs that are set up as independent sinks can
be enabled individually in Register 0x10. They can also all be
enabled simultaneously via the SIS_EN bit in Register 0x01.
Any LEDs configured for the backlight can only be enabled
via the BL_EN bit in Register 0x01.
LED CURRENT SETTINGS
30
25
20
15
10
5
LINEAR
SQUARE
Any of the LED outputs (Pin D1 to Pin D7) can be used to
drive any color of LED at 0 mA to 30 mA, provided that the
0
0
32
64
96
128
LED’s Vf is less than 4.1 V. Additionally, the D7 sink can regu-
late up to 60 mA. The current settings are determined by a
7-bit code programmed by the user into Register 0x14 through
Register 0x1A (for the independent sinks) and Register 0x09 to
Register 0x0E (for the backlight sinks). The 7-bit resolution
allows the user to set the LED to one of 128 different levels.
The ADP8863 can implement two distinct algorithms to
achieve a linear or a nonlinear relationship between input
code and diode output current. The law and SC_LAW bits
in Register 0x04 and Register 0x0F, respectively, are used to
change between these algorithms.
CODE
Figure 29. LED Current vs. Input Code
AUTOMATED FADE IN AND FADE OUT
The LED drivers are easily configured for automated fade in
and fade out. Sixteen fade in and fade out rates can be selected
via the I 2 C interface. Fade in and fade out rates range from
0.0 sec to 5.5 sec (per full-scale current, either 30 mA or 60 mA).
The backlight LEDs have separate fade in and fade out time
controls from the independent sink LEDs.
Table 5. Available Fade In and Fade Out Rates
By default, the ADP8863 uses a linear algorithm (law and
SC_LAW = 00), where the LED current increases linearly for
a corresponding increase in input code. LED current (in
milliamperes) is determined by the following equation:
LED Current (mA) = Code × ( Full-Scale Current /127)
where:
Code is the input code programmed by the user.
Full-Scale Current is the maximum sink current allowed per
LED (typically 30 mA).
(2)
Code
0000
0001
0010
0011
0100
0101
0110
0111
1000
Fade Rate (in sec per Full-Scale Current)
0.0 (disabled)
0.3
0.6
0.9
1.2
1.5
1.8
2.1
2.4
?
?
Full ? Scale Current
LED Current ( mA ) = ? Code ×
?
?
?
?
?
The ADP8863 can also implement a nonlinear (square
approximation) relationship between input code and LED
current. In this case (law and SC_LAW = 01, 10, or 11), the LED
current (in milliamperes) is determined by the following
equation:
2
(3)
127
Figure 29 shows the LED current level vs. input code for both
the linear and square law algorithms.
1001 2.7
1010 3.0
1011 3.5
1100 4.0
1101 4.5
1110 5.0
1111 5.5
The fade profile is based on the transfer law selected (linear,
square, Cubic 10, or Cubic 11) and the delta between the actual
current and the target current. Smaller changes in current
reduce the fade time. For linear and square law fades, the fade
time is given by
Fade Time = Fade Rate × ( Code /127)
where the Fade Rate is shown in Table 5.
Rev. A | Page 14 of 52
(4)
相关PDF资料 |
PDF描述 |
|---|---|
| ADUM1100UR | IC DIGITAL ISOL/COUPLER 8SOIC |
| ADUM1201CR | IC ISOLATOR DIGITAL DUAL 8SOIC |
| ADUM1210BRZ | IC ISOLATOR DIGITAL DUAL 8SOIC |
| ADUM1233BRWZ-RL | IC ISOLATR DGTL 2CH 0.1A 16-SOIC |
| ADUM1234BRWZ-RL | IC ISOLATR DGTL 2CH 0.1A 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP8863DBCP-EVALZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Charge Pump,7-Channel Fun Lighting LED Driver |
| ADP8866 | 制造商:AD 制造商全称:Analog Devices 功能描述:Charge Pump Driven 9-Channel LED Driver with Automated LED Lighting Effects |
| ADP8866ACPZ-R7 | 功能描述:IC LED DVR WHIT BCKLGT 20LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| ADP8866CP-EVALZ | 功能描述:BOARD DAUGHTER ADP8866 LFCSP RoHS:是 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:- 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| ADP886XMB1-EVALZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Charge Pump, 7-Channel Smart LED Driver with I2C Interface |
发布紧急采购，3分钟左右您将得到回复。