- 您现在的位置：买卖IC网 > Datasheet目录308 > ADP8863ACPZ-R7 (Analog Devices Inc)IC LED DRVR WHIT BCKLGT 20-WLCSP Datasheet资料下载
参数资料
| 型号： | ADP8863ACPZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 18/52页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHIT BCKLGT 20-WLCSP |
| 标准包装： | 1 |
| 拓扑： | 切换式电容器（充电泵） |
| 输出数： | 7 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，LED 闪烁器 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 800kHz ~ 1.32MHz |
| 电源电压： | 2.5 V ~ 5.5 V |
| 输出电压： | 4.3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-UFBGA，WLCSP |
| 供应商设备封装： | 20-WLCSP |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | ADP8863ACPZ-R7DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
ADP8863
L2_TRIP
L2_EN
L2_HYS
L2_OUT
ware may select the comparator of the phototransistor that is
exposed to higher light intensity to control the transition
between the programmed backlight intensity levels.
The L2_CMPR and L3_CMPR comparators can be enabled
independently of each other, or they can operate simultaneously. A
PHOTO
SENSOR
OUTPUT
ADC
FILTER
SETTINGS
L3_TRIP
L3_HYS
L3_OUT
single conversion from each ADC takes 80 ms (typical). When
CMP_AUTOEN is set for automatic backlight adjustment (see
the Automatic Backlight Adjustment section), the ADC and
comparators run continuously. If the backlight is disabled and
at least one independent sink is enabled, it is possible to use the
light sensor comparators in a single-shot mode. A single-shot read
L3_EN
Figure 41. Ambient Light Sensing and Trip Comparators
The L2 comparator, L2_CMPR, detects when the photosensor
output has dropped below the programmable L2_TRP point
(Register 0x1D). If this event occurs, then the L2_OUT status
signal is set. L2_CMPR contains programmable hysteresis,
meaning that the photosensor output must rise above L2_TRP +
L2_HYS before L2_OUT clears. L2_CMPR is enabled via the
L2_EN bit. The L2_TRP and L2_HYS values of L2_CMPR can
be set between 0 μA and 1080 μA (typical) in steps of 4.3 μA
(typical).
The L3 comparator, L3_CMPR, detects when the photosensor
output drops below the programmable L3_TRP point (Register
0x1F). If this event occurs, the L3_OUT status signal is set.
L3_CMPR contains programmable hysteresis, meaning that the
photosensor output must rise above L3_TRP + L3_HYS before
L3_OUT clears. L3_CMPR is enabled via the L3_EN bit. The
L3_TRP and L3_HYS values of L3_CMPR can be set between
0 μA and 137.7 μA (typical) in steps of 0.54 μA (typical).
L2_TRP
L2_HYS
L3_TRP
L3_HYS
of the photocomparators is performed by setting the FORCE_RD
bit in Register 0x1B. After the single-shot measurement is com-
pleted, the internal state machine clears the FORCE_RD bit.
The interrupt flags (CMP_INT and CMP_INT2) can be used to
notify the system when either L2 or L3 changes state. See the
Interrupts section for more information.
AUTOMATIC BACKLIGHT ADJUSTMENT
The ambient light sensor comparators can automatically transi-
tion the backlight between one of its three operating levels. To
enable this mode, set the CMP_AUTOEN bit in Register 0x01.
When I 2 C selection is enabled, the internal state machine takes
control of the BLV bits and changes them based on the L2_OUT
and L3_OUT status bits. When L2_OUT is set high, it indicates
that the ambient light conditions have dropped below the
L2_TRP point and that the backlight should move to its office
(L2) level. When L3_OUT is set high, it indicates that ambient light
conditions have dropped below the L3_TRP point and that the
backlight should move to its dark (L3) level. Table 6 shows the
relationship between backlight operation and the ambient light
sensor comparator outputs.
The L3_OUT status bit has greater priority; therefore, if
L3_OUT is set, the backlight operates at L3 (dark) even if
L2_OUT is also set.
Filter times from 80 ms to 10 sec can be programmed for the
comparators (Register 0x1B and Register 0x1C) before they
1
10
100
1000
change state.
ADC RANGE (μA)
Table 6. Comparator Output Truth Table
Figure 42. Comparator Ranges
Note that the full-scale value of the L2_TRP and L2_HYS
CMP_AUTOEN
0
L3_OUT
X 1
L2_OUT
X 1
Backlight Operation
BLV can be manually set
registers is 250 (decimal). Therefore, if the value of L2_TRP +
by the user
L2_HYS exceeds 250, the comparator output is unable to
1
0
0
BLV = 00, backlight
deassert. For example, if L2_TRP is set to 204 (80% of the full-
operates at L1 (daylight)
X is the don’t care bit.
scale value, or approximately 0.80 × 1080 μA = 864 μA), then
L2_HYS must be set to less than 46 (250 ? 204 = 46). If it is not,
then L2_HYS + L2_TRP exceeds 250 and the L2_CMPR
comparator is never allowed to go low.
1 0
1 1
1
1
X 1
BLV = 01, backlight
operates at L2 (office)
BLV = 10, backlight
operates at L3 (dark)
When both phototransistors are enabled and programmed in
automatic mode (through Bit CMP_AUTOEN in Register
0x01), the user application must determine which comparator
outputs to use, by selecting Bit SEL_AB in Register 0x04 for
automatic light sensing transitions. For example, the user soft-
Rev. A | Page 18 of 52
相关PDF资料 |
PDF描述 |
|---|---|
| ADUM1100UR | IC DIGITAL ISOL/COUPLER 8SOIC |
| ADUM1201CR | IC ISOLATOR DIGITAL DUAL 8SOIC |
| ADUM1210BRZ | IC ISOLATOR DIGITAL DUAL 8SOIC |
| ADUM1233BRWZ-RL | IC ISOLATR DGTL 2CH 0.1A 16-SOIC |
| ADUM1234BRWZ-RL | IC ISOLATR DGTL 2CH 0.1A 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP8863DBCP-EVALZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Charge Pump,7-Channel Fun Lighting LED Driver |
| ADP8866 | 制造商:AD 制造商全称:Analog Devices 功能描述:Charge Pump Driven 9-Channel LED Driver with Automated LED Lighting Effects |
| ADP8866ACPZ-R7 | 功能描述:IC LED DVR WHIT BCKLGT 20LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| ADP8866CP-EVALZ | 功能描述:BOARD DAUGHTER ADP8866 LFCSP RoHS:是 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:- 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| ADP886XMB1-EVALZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Charge Pump, 7-Channel Smart LED Driver with I2C Interface |
发布紧急采购，3分钟左右您将得到回复。