- 您现在的位置：买卖IC网 > Datasheet目录308 > ADP8863ACPZ-R7 (Analog Devices Inc)IC LED DRVR WHIT BCKLGT 20-WLCSP Datasheet资料下载
参数资料
| 型号： | ADP8863ACPZ-R7 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 23/52页 |
| 文件大小： | 0K |
| 描述： | IC LED DRVR WHIT BCKLGT 20-WLCSP |
| 标准包装： | 1 |
| 拓扑： | 切换式电容器（充电泵） |
| 输出数： | 7 |
| 内部驱动器： | 是 |
| 类型 - 主要： | 背光，LED 闪烁器 |
| 类型 - 次要： | RGB，白色 LED |
| 频率： | 800kHz ~ 1.32MHz |
| 电源电压： | 2.5 V ~ 5.5 V |
| 输出电压： | 4.3 V ~ 5.5 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-UFBGA，WLCSP |
| 供应商设备封装： | 20-WLCSP |
| 包装： | 标准包装 |
| 工作温度： | -40°C ~ 85°C |
| 其它名称： | ADP8863ACPZ-R7DKR |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页当前第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页
ADP8863
APPLICATIONS INFORMATION
The ADP8863 allows the charge pump to operate efficiently with a
voltage drop across the regulating current source. This gives
minimum of external components. Specifically, the user must
select an input capacitor (C IN ), output capacitor (C OUT ), and two
charge pump fly capacitors (C1 and C2). C IN should be 1 μF or
greater. The value must be high enough to produce a stable input
V OUT = Vf (MAX) + V DX
Combining Equation 8 and Equation 9 gives
V IN = ( Vf (MAX) + V DX + I OUT × R OUT ( G ))/ G
(9)
(10)
voltage signal at the minimum input voltage and maximum
output load. A 1 μF capacitor for C OUT is recommended. Larger
values are permissible, but care must be exercised to ensure that
VOUT charges above 55% (typical) of V IN within 4 ms (typical).
See the Short-Circuit Protection Mode section for more details.
For best practice, it is recommended that the two charge pump fly
capacitors be 1 μF; larger values are not recommended, and smaller
values may reduce the ability of the charge pump to deliver
maximum current. For optimal efficiency, the charge pump fly
capacitors should have low equivalent series resistance (ESR). Low
ESR X5R or X7R capacitors are recommended for all four compo-
nents. The use of fly capacitors sized 0402 and smaller is allowed,
but the GDWN_DIS bit in Register 0x01 must be set. Minimum
voltage ratings should adhere to the guidelines in Table 7.
Table 7. Capacitor Stress in Each Charge Pump Gain State
Capacitor Gain = 1× Gain = 1.5× Gain = 2×
C IN V IN V IN V IN
C OUT V IN V IN × 1.5 (max of 5.5 V) V IN × 2.0 (max of 5.5 V)
C1 None V IN /2 V IN
Equation 10 is useful for calculating approximate bounds for the
charge pump design.
Determining the Transition Point of the Charge Pump
Consider the following design example, where:
Vf (MAX) = 3.7 V
I OUT = 140 mA (7 LEDs at 20 mA each)
R OUT (G = 1.5×) = 3 Ω (obtained from Figure 13)
At the point of a gain transition, V DX = V HR(UP) . Table 1 gives the
typical value of V HR(UP) as 0.2 V. Therefore, the input voltage
level when the gain transitions from 1.5× to 2× is
V IN = (3.7 V + 0.2 V + 140 mA × 3 Ω)/1.5 = 2.88 V
LAYOUT GUIDELINES
Note the following layout guidelines:
? For optimal noise immunity, place the C IN and C OUT capaci-
tors as close as possible to their respective pins. These
capacitors should share a short ground trace. If the LEDs
are a significant distance from the VOUT pin, another capaci-
C2
None
V IN /2
V IN
tor on VOUT, placed closer to the LEDs, is advisable.
If one or both ambient light sensor comparator inputs (CMP_IN
and D6) are used, a small capacitor (0.1 μF is recommended)
must be connected from the input to ground.
Any color LED can be used if the Vf (forward voltage) is less
than 4.1 V. However, using lower Vf LEDs reduces the input
power consumption by allowing the charge pump to operate at
lower gain states.
The equivalent circuit model for a charge pump is shown in
?
?
?
For optimal efficiency, place the charge pump fly capacitors
(C1 and C2) as close to the part as possible.
The ADP8863 does not distinguish between power ground
and analog ground. Therefore, both ground pins can be
connected directly together. It is recommended that these
ground pins be connected at the ground for the input and
output capacitors.
The LFCSP package requires the exposed pad to be
soldered at the board to the GND1 and/or GND2 pin(s).
Figure 48.
R OUT
VOUT
I OUT
?
Unused diode pins (Pin D1 to Pin D7) can be connected to
ground or to VOUT, or remain floating. However, the
unused diode current sinks must be disabled by setting
G × V IN
C OUT
V DX
them as independent sinks in Register 0x05 and then
disabling them in Register 0x10. If they are not disabled,
the charge pump efficiency may suffer.
Figure 48. Charge Pump Equivalent Circuit Model
The input voltage is multiplied by the gain (G) and delivered to
the output through an effective resistance (R OUT ). The output
current flows through R OUT and produces an IR drop to yield
?
?
If the CMP_IN phototransistor input is not used, it can be
connected to ground or remain floating.
If the interrupt pin (nINT) is not used, connect it to ground
or leave it floating. Never connect it to a voltage supply,
except through a ≥1 kΩ series resistor.
V OUT = G × V IN ? I OUT × R OUT ( G )
(8)
?
The ADP8863 has an integrated noise filter on the nRST
The R OUT term is a combination of the R DSON resistance for the
switches used in the charge pump and a small resistance that accounts
for the effective dynamic charge pump resistance. The R OUT level
changes based upon the gain (the configuration of the switches).
Typical R OUT values are given in Table 1, Figure 13, and Figure 14.
V OUT is also equal to the largest Vf of the LEDs used plus the
Rev. A | Page 23 of 52
pin. Under normal conditions, it is not necessary to filter
the reset line. However, if the part is exposed to an unusually
noisy signal, it is beneficial to add a small RC filter or bypass
capacitor on this pin. If the nRST pin is not used, it must
be pulled well above the V IH(MIN) level (see Table 1). Do not
allow the nRST pin to float.
相关PDF资料 |
PDF描述 |
|---|---|
| ADUM1100UR | IC DIGITAL ISOL/COUPLER 8SOIC |
| ADUM1201CR | IC ISOLATOR DIGITAL DUAL 8SOIC |
| ADUM1210BRZ | IC ISOLATOR DIGITAL DUAL 8SOIC |
| ADUM1233BRWZ-RL | IC ISOLATR DGTL 2CH 0.1A 16-SOIC |
| ADUM1234BRWZ-RL | IC ISOLATR DGTL 2CH 0.1A 16-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADP8863DBCP-EVALZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Charge Pump,7-Channel Fun Lighting LED Driver |
| ADP8866 | 制造商:AD 制造商全称:Analog Devices 功能描述:Charge Pump Driven 9-Channel LED Driver with Automated LED Lighting Effects |
| ADP8866ACPZ-R7 | 功能描述:IC LED DVR WHIT BCKLGT 20LFCSP RoHS:是 类别:集成电路 (IC) >> PMIC - LED 驱动器 系列:- 标准包装:60 系列:- 恒定电流:- 恒定电压:- 拓扑:线性（LDO），PWM，升压（升压） 输出数:8 内部驱动器:是 类型 - 主要:背光 类型 - 次要:RGB，白色 LED 频率:500kHz ~ 1.5MHz 电源电压:4.75 V ~ 26 V 输出电压:45V 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* 工作温度:-40°C ~ 85°C |
| ADP8866CP-EVALZ | 功能描述:BOARD DAUGHTER ADP8866 LFCSP RoHS:是 类别:编程器，开发系统 >> 评估板 - LED 驱动器 系列:- 标准包装:1 系列:PowerWise® 电流 - 输出 / 通道:20mA 输出及类型:1，非隔离 输出电压:17V 特点:可调光 输入电压:2.7 ~ 5.5 V 已供物品:板 已用 IC / 零件:LM3508 相关产品:LM3508TLX-ND - IC LED DRVR WHT BCKLGT 9USMDLM3508TLDKR-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLCT-ND - IC LED DRVR WHT BCKLGT 9MICROSMDLM3508TLTR-ND - IC LED DRVR WHT BCKLGT 9MICROSMD |
| ADP886XMB1-EVALZ | 制造商:AD 制造商全称:Analog Devices 功能描述:Charge Pump, 7-Channel Smart LED Driver with I2C Interface |
发布紧急采购，3分钟左右您将得到回复。