- 您现在的位置：买卖IC网 > PDF目录19399 > ADSP-21478KSWZ-1A (Analog Devices Inc)IC DSP SHARC 200MHZ LP 100LQFP PDF资料下载
参数资料
| 型号： | ADSP-21478KSWZ-1A |
| 厂商： | Analog Devices Inc |
| 文件页数： | 2/72页 |
| 文件大小： | 0K |
| 描述： | IC DSP SHARC 200MHZ LP 100LQFP |
| 标准包装： | 1 |
| 系列： | SHARC® |
| 类型： | 浮点 |
| 接口： | DAI，DPI，EBI/EMI，I²C，SPI，SPORT，UART/USART |
| 时钟速率： | 200MHz |
| 非易失内存： | ROM（4Mb） |
| 芯片上RAM： | 3Mb |
| 电压 - 输入/输出： | 3.30V |
| 电压 - 核心： | 1.20V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 100-LQFP 裸露焊盘 |
| 供应商设备封装： | 100-LQFP-EP（14x14） |
| 包装： | 托盘 |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页
Rev. A
|
Page 10 of 72
|
September 2011
Digital Peripheral Interface (DPI)
The digital peripheral interface provides connections to two
serial peripheral interface ports (SPI), one universal asynchro-
nous receiver-transmitter (UART), 12 flags, a 2-wire interface
(TWI), three PWM modules (PWM3–1), and two general-
purpose timers.
Serial Peripheral (Compatible) Interface (SPI)
The SPI is an industry-standard synchronous serial link,
enabling the SPI-compatible port to communicate with other
SPI compatible devices. The SPI consists of two data pins, one
device select pin, and one clock pin. It is a full-duplex synchro-
nous serial interface, supporting both master and slave modes.
The SPI port can operate in a multimaster environment by
interfacing with up to four other SPI-compatible devices, either
acting as a master or slave device. The SPI-compatible periph-
eral implementation also features programmable baud rate and
clock phase and polarities. The SPI-compatible port uses open
drain drivers to support a multimaster configuration and to
avoid data contention.
UART Port
The processors provide a full-duplex Universal Asynchronous
Receiver/Transmitter (UART) port, which is fully compatible
with PC-standard UARTs. The UART port provides a simpli-
fied UART interface to other peripherals or hosts, supporting
full-duplex, DMA-supported, asynchronous transfers of serial
data. The UART also has multiprocessor communication capa-
bility using 9-bit address detection. This allows it to be used in
multidrop networks through the RS-485 data interface
standard. The UART port also includes support for 5 to 8 data
bits, 1 or 2 stop bits, and none, even, or odd parity. The UART
port supports two modes of operation:
PIO (programmed I/O) – The processor sends or receives
data by writing or reading I/O-mapped UART registers.
The data is double-buffered on both transmit and receive.
DMA (direct memory access) – The DMA controller trans-
fers both transmit and receive data. This reduces the
number and frequency of interrupts required to transfer
data to and from memory. The UART has two dedicated
DMA channels, one for transmit and one for receive. These
DMA channels have lower default priority than most DMA
channels because of their relatively low service rates.
The UART port's baud rate, serial data format, error code gen-
eration and status, and interrupts are programmable:
Support for bit rates ranging from (fPCLK/1,048,576) to
(fPCLK/16) bits per second.
Support for data formats from 7 to 12 bits per frame.
Both transmit and receive operations can be configured to
generate maskable interrupts to the processor.
In conjunction with the general-purpose timer functions, auto-
baud detection is supported.
Pulse-Width Modulation
The PWM module is a flexible, programmable, PWM waveform
generator that can be programmed to generate the required
switching patterns for various applications related to motor and
engine control or audio power control. The PWM generator can
generate either center-aligned or edge-aligned PWM wave-
forms. In addition, it can generate complementary signals on
two outputs in paired mode or independent signals in non-
paired mode (applicable to a single group of four PWM
waveforms).
The entire PWM module has four groups of four PWM outputs
generating 16 PWM outputs in total. Each PWM group pro-
duces two pairs of PWM signals on the four PWM outputs.
The PWM generator is capable of operating in two distinct
modes while generating center-aligned PWM waveforms: single
update mode or double update mode. In single update mode the
duty cycle values are programmable only once per PWM period.
This results in PWM patterns that are symmetrical about the
midpoint of the PWM period. In double update mode, a second
updating of the PWM registers is implemented at the midpoint
of the PWM period. In this mode, it is possible to produce
asymmetrical PWM patterns that produce lower harmonic dis-
tortion in three-phase PWM inverters.
PWM signals can be mapped to the external port address lines
or to the DPI pins.
Timers
The processors have a total of three timers: a core timer that can
generate periodic software interrupts and two general-purpose
timers that can generate periodic interrupts and be indepen-
dently set to operate in one of three modes:
Pulse waveform generation mode
Pulse width count/capture mode
External event watch dog mode
The core timer can be configured to use FLAG3 as a timer
expired signal, and the general-purpose timers have one bidirec-
tional pin and four registers that implement its mode of
operation: a 6-bit configuration register, a 32-bit count register,
a 32-bit period register, and a 32-bit pulse width register. A sin-
gle control and status register enables or disables the general-
purpose timer.
2-Wire Interface Port (TWI)
The TWI is a bidirectional 2-wire, serial bus used to move 8-bit
data while maintaining compliance with the I2C bus protocol.
The TWI master incorporates the following features:
7-bit addressing
Simultaneous master and slave operation on multiple
device systems with support for multi master data
arbitration
Digital filtering and timed event processing
100 kbps and 400 kbps data rates
Low interrupt rate
相关PDF资料 |
PDF描述 |
|---|---|
| ACM30DTMH | CONN EDGECARD 60POS R/A .156 SLD |
| VI-J6K-IZ | CONVERTER MOD DC/DC 40V 25W |
| ACM30DTMD | CONN EDGECARD 60POS R/A .156 SLD |
| TAJC335M050RNJ | CAP TANT 3.3UF 50V 20% 2312 |
| RW2-1209D/H2/SMD | CONV DC/DC 2W 9-18VIN +/-09VOUT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADSP-21478KSWZ-2A | 功能描述:IC DSP SHARC 266MHZ LP 100LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:SHARC® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-21478KSWZ-ENG | 制造商:Analog Devices 功能描述:SHARC PROCESSOR - Trays |
| ADSP-21479 | 制造商:AD 制造商全称:Analog Devices 功能描述:SHARC Processor |
| ADSP-21479BBCZ-2A | 功能描述:IC DSP SHARC 266MHZ LP 196CSPBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:SHARC® 标准包装:2 系列:StarCore 类型:SC140 内核 接口:DSI，以太网，RS-232 时钟速率:400MHz 非易失内存:外部 芯片上RAM:1.436MB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:-40°C ~ 105°C 安装类型:表面贴装 封装/外壳:431-BFBGA，FCBGA 供应商设备封装:431-FCPBGA（20x20） 包装:托盘 |
| ADSP-21479BBCZ-2AX | 制造商:Analog Devices 功能描述:- Trays |
发布紧急采购，3分钟左右您将得到回复。