- 您现在的位置：买卖IC网 > PDF目录19388 > ADSP-BF537BBCZ-5B (Analog Devices Inc)IC DSP CTLR 16BIT 208CSPBGA PDF资料下载
参数资料
| 型号： | ADSP-BF537BBCZ-5B |
| 厂商： | Analog Devices Inc |
| 文件页数： | 67/68页 |
| 文件大小： | 0K |
| 描述： | IC DSP CTLR 16BIT 208CSPBGA |
| 产品培训模块： | Blackfin® Processor Core Architecture Overview Blackfin® Device Drivers Blackfin® Optimizations for Performance and Power Consumption Blackfin® System Services |
| 标准包装： | 1 |
| 系列： | Blackfin® |
| 类型： | 定点 |
| 接口： | CAN，SPI，SSP，TWI，UART |
| 时钟速率： | 500MHz |
| 非易失内存： | 外部 |
| 芯片上RAM： | 132kB |
| 电压 - 输入/输出： | 2.50V，3.30V |
| 电压 - 核心： | 1.26V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 208-LFBGA，CSPBGA |
| 供应商设备封装： | 208-CSPBGA |
| 包装： | 托盘 |
| 配用： | ADZS-BF537-ASKIT-ND - BOARD EVAL SKIT ADSP-BF537 ADZS-BFAUDIO-EZEXT-ND - BOARD EVAL AUDIO BLACKFIN ADZS-BF537-EZLITE-ND - BOARD EVAL ADSP-BF537 ADZS-BFAV-EZEXT-ND - BOARD DAUGHT ADSP-BF533,37,61KIT ADZS-BF537-STAMP-ND - SYSTEM DEV FOR ADSP-BF537 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页当前第67页第68页
Rev. J
|
Page 8 of 68
|
February 2014
Event Control
The Blackfin processor provides a very flexible mechanism to
control the processing of events. In the CEC, three registers are
used to coordinate and control events. Each register is
32 bits wide:
CEC interrupt latch register (ILAT) – Indicates when
events have been latched. The appropriate bit is set when
the processor has latched the event and cleared when the
event has been accepted into the system. This register is
updated automatically by the controller, but it can be writ-
ten only when its corresponding IMASK bit is cleared.
CEC interrupt mask register (IMASK) – Controls the
masking and unmasking of individual events. When a bit is
set in the IMASK register, that event is unmasked and is
processed by the CEC when asserted. A cleared bit in the
IMASK register masks the event, preventing the processor
from servicing the event even though the event may be
latched in the ILAT register. This register can be read or
written while in supervisor mode. (Note that general-pur-
pose interrupts can be globally enabled and disabled with
the STI and CLI instructions, respectively.)
CEC interrupt pending register (IPEND) – The IPEND
register keeps track of all nested events. A set bit in the
IPEND register indicates the event is currently active or
nested at some level. This register is updated automatically
by the controller but can be read while in supervisor mode.
The SIC allows further control of event processing by providing
three 32-bit interrupt control and status registers. Each register
contains a bit corresponding to each of the peripheral interrupt
events shown in Table 3 on Page 7.
SIC interrupt mask register (SIC_IMASK) – Controls the
masking and unmasking of each peripheral interrupt event.
When a bit is set in the register, that peripheral event is
unmasked and is processed by the system when asserted. A
cleared bit in the register masks the peripheral event, pre-
venting the processor from servicing the event.
SIC interrupt status register (SIC_ISR) – As multiple
peripherals can be mapped to a single event, this register
allows the software to determine which peripheral event
source triggered the interrupt. A set bit indicates the
peripheral is asserting the interrupt, and a cleared bit indi-
cates the peripheral is not asserting the event.
SIC interrupt wake-up enable register (SIC_IWR) – By
enabling the corresponding bit in this register, a peripheral
can be configured to wake up the processor, should the
core be idled when the event is generated. (For more infor-
Because multiple interrupt sources can map to a single general-
purpose interrupt, multiple pulse assertions can occur simulta-
neously, before or during interrupt processing for an interrupt
event already detected on this interrupt input. The IPEND reg-
ister contents are monitored by the SIC as the interrupt
acknowledgement.
The appropriate ILAT register bit is set when an interrupt rising
edge is detected (detection requires two core clock cycles). The
bit is cleared when the respective IPEND register bit is set. The
IPEND bit indicates that the event has entered into the proces-
sor pipeline. At this point the CEC recognizes and queues the
next rising edge event on the corresponding event input. The
minimum latency from the rising edge transition of the general-
purpose interrupt to the IPEND output asserted is three core
clock cycles; however, the latency can be much higher, depend-
ing on the activity within and the state of the processor.
DMA CONTROLLERS
The Blackfin processors have multiple, independent DMA
channels that support automated data transfers with minimal
overhead for the processor core. DMA transfers can occur
between the processor’s internal memories and any of its DMA-
capable peripherals. Additionally, DMA transfers can be accom-
plished between any of the DMA-capable peripherals and
external devices connected to the external memory interfaces,
including the SDRAM controller and the asynchronous mem-
ory controller. DMA-capable peripherals include the Ethernet
MAC (ADSP-BF536 and ADSP-BF537 only), SPORTs, SPI port,
UARTs, and PPI. Each individual DMA-capable peripheral has
at least one dedicated DMA channel.
The DMA controller supports both one-dimensional (1-D) and
two-dimensional (2-D) DMA transfers. DMA transfer initial-
ization can be implemented from registers or from sets of
parameters called descriptor blocks.
The 2-D DMA capability supports arbitrary row and column
sizes up to 64K elements by 64K elements, and arbitrary row
and column step sizes up to ±32K elements. Furthermore, the
column step size can be less than the row step size, allowing
implementation of interleaved data streams. This feature is
especially useful in video applications where data can be de-
interleaved on the fly.
Examples of DMA types supported by the DMA controller
include
A single, linear buffer that stops upon completion
A circular, auto-refreshing buffer that interrupts on each
full or fractionally full buffer
1-D or 2-D DMA using a linked list of descriptors
2-D DMA using an array of descriptors, specifying only the
base DMA address within a common page.
DMA Channels 12 and 13
(Memory DMA Stream 0)
IVG13
29
DMA Channels 14 and 15
(Memory DMA Stream 1)
IVG13
30
Software Watchdog Timer
IVG13
31
Port F Interrupt B
IVG13
31
Table 3. System Interrupt Controller (SIC) (Continued)
Peripheral Interrupt Event
Default
Mapping
Peripheral
Interrupt ID
相关PDF资料 |
PDF描述 |
|---|---|
| ADSP-BF534YBCZ-4B | IC DSP CTLR 16BIT 400MHZ 208-CSP |
| ADSP-21488BSWZ-3A | IC DSP 3MBIT 400MHZ 100LQFP |
| ADSP-BF544MBBCZ-5M | IC DSP 16BIT 533MHZ MDDR 400CBGA |
| SWS600L-5 | POWER SUPPLY 5V 120A SGL OUTPUT |
| ADSP-BF544BBCZ-5A | IC DSP 16BIT 533MHZ 400CSBGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADSP-BF537BBCZ-5BV | 功能描述:IC DSP CTLR 16BIT 208CSPBGA RoHS:是 类别:集成电路 (IC) >> 嵌入式 - DSP（数字式信号处理器） 系列:Blackfin® 标准包装:40 系列:TMS320DM64x, DaVinci™ 类型:定点 接口:I²C，McASP，McBSP 时钟速率:400MHz 非易失内存:外部 芯片上RAM:160kB 电压 - 输入/输出:3.30V 电压 - 核心:1.20V 工作温度:0°C ~ 90°C 安装类型:表面贴装 封装/外壳:548-BBGA，FCBGA 供应商设备封装:548-FCBGA（27x27） 包装:托盘 配用:TMDSDMK642-0E-ND - DEVELPER KIT W/NTSC CAMERA296-23038-ND - DSP STARTER KIT FOR TMS320C6416296-23059-ND - FLASHBURN PORTING KIT296-23058-ND - EVAL MODULE FOR DM642TMDSDMK642-ND - DEVELOPER KIT W/NTSC CAMERA |
| ADSP-BF537BBCZ5BVX | 制造商:Analog Devices 功能描述:- Trays |
| ADSP-BF537BBCZ-5BX | 制造商:Analog Devices 功能描述:208-MEG PB FREE SPARSE - Trays |
| ADSP-BF537KBC-6A | 制造商:Analog Devices 功能描述:DSP FIX PT 16BIT 600MHZ 600MIPS 182CSPBGA - Trays |
| ADSP-BF537KBCZ-6A | 制造商:Analog Devices 功能描述:DSP Fixed-Point 16-Bit 600MHz 600MIPS 182-Pin CSP-BGA 制造商:Analog Devices 功能描述:Digital Signal Processor IC |
发布紧急采购，3分钟左右您将得到回复。