- 您现在的位置：买卖IC网 > PDF目录11205 > ADUC7021BCPZ62-RL (Analog Devices Inc)IC MCU 12BIT 1MSPS UART 40-LFCSP PDF资料下载
参数资料
| 型号： | ADUC7021BCPZ62-RL |
| 厂商： | Analog Devices Inc |
| 文件页数： | 67/104页 |
| 文件大小： | 0K |
| 描述： | IC MCU 12BIT 1MSPS UART 40-LFCSP |
| 标准包装： | 2,500 |
| 系列： | MicroConverter® ADuC7xxx |
| 核心处理器： | ARM7 |
| 芯体尺寸： | 16/32-位 |
| 速度： | 44MHz |
| 连通性： | EBI/EMI，I²C，SPI，UART/USART |
| 外围设备： | PLA，PWM，PSM，温度传感器，WDT |
| 输入/输出数： | 13 |
| 程序存储器容量： | 64KB（32K x 16） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 2K x 32 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 3.6 V |
| 数据转换器： | A/D 8x12b，D/A 2x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 40-VFQFN 裸露焊盘，CSP |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页当前第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页
Data Sheet
ADuC7019/20/21/22/24/25/26/27/28/29
Rev. F | Page 65 of 104
Output Control Unit
The operation of the output control unit is controlled by the
9-bit read/write PWMEN register. This register controls two
distinct features of the output control unit that are directly
useful in the control of electronic counter measures (ECM) or
binary decimal counter measures (BDCM). The PWMEN
register contains three crossover bits, one for each pair of PWM
outputs. Setting Bit 8 of the PWMEN register enables the
crossover mode for the 0H/0L pair of PWM signals, setting
Bit 7 enables crossover on the 1H/1L pair of PWM signals, and
setting Bit 6 enables crossover on the 2H/2L pair of PWM
signals. If crossover mode is enabled for any pair of PWM
signals, the high-side PWM signal from the timing unit (0H, for
example) is diverted to the associated low-side output of the
output control unit so that the signal ultimately appears at the
PWM0L pin. Of course, the corresponding low-side output of
the timing unit is also diverted to the complementary high-side
output of the output control unit so that the signal appears at
the PWM0H pin. Following a reset, the three crossover bits are
cleared, and the crossover mode is disabled on all three pairs of
PWM signals. The PWMEN register also contains six bits (Bit 0
to Bit 5) that can be used to individually enable or disable each
of the six PWM outputs. If the associated bit of the PWMEN
register is set, the corresponding PWM output is disabled
regardless of the corresponding value of the duty cycle register.
This PWM output signal remains in the off state as long as the
corresponding enable/disable bit of the PWMEN register is set.
The implementation of this output enable function is imple-
mented after the crossover function.
Following a reset, all six enable bits of the PWMEN register are
cleared, and all PWM outputs are enabled by default. In a manner
identical to the duty cycle registers, the PWMEN is latched on
the rising edge of the PWMSYNC signal. As a result, changes to
this register become effective only at the start of each PWM cycle
in single update mode. In double update mode, the PWMEN
register can also be updated at the midpoint of the PWM cycle.
In the control of an ECM, only two inverter legs are switched at
any time, and often the high-side device in one leg must be
switched on at the same time as the low-side driver in a second
leg. Therefore, by programming identical duty cycle values for
two PWM channels (for example, PWMCH0 = PWMCH1) and
setting Bit 7 of the PWMEN register to cross over the 1H/1L
pair of PWM signals, it is possible to turn on the high-side
switch of Phase A and the low-side switch of Phase B at the
same time. In the control of ECM, it is usual for the third
inverter leg (Phase C in this example) to be disabled for a
number of PWM cycles. This function is implemented by
disabling both the 2H and 2L PWM outputs by setting Bit 0
and Bit 1 of the PWMEN register.
This situation is illustrated in Figure 71, where it can be seen
that both the 0H and 1L signals are identical because
PWMCH0 = PWMCH1 and the crossover bit for Phase B is set.
04
95
5-
0
30
PWMCH0 =
PWMCH1
0H
0L
1H
1L
2H
2L
PWMCH0 =
PWMCH1
2 × PWMDAT1
PWMDAT0
Figure 71. Active Low PWM Signals Suitable for ECM Control,
PWMCH0 = PWMCH1, Crossover 1H/1L Pair and Disable
0L, 1H, 2H, and 2L Outputs in Single Update Mode.
In addition, the other four signals (0L, 1H, 2H, and 2L) have
been disabled by setting the appropriate enable/disable bits of
the PWMEN register. In Figure 71, the appropriate value for
the PWMEN register is 0x00A7. In normal ECM operation,
each inverter leg is disabled for certain periods of time to
change the PWMEN register based on the position of the rotor
shaft (motor commutation).
Gate Drive Unit
The gate drive unit of the PWM controller adds features that
simplify the design of isolated gate-drive circuits for PWM
inverters. If a transformer-coupled, power device, gate-drive
amplifier is used, the active PWM signal must be chopped at a
high frequency. The 16-bit read/write PWMCFG register
programs this high frequency chopping mode. The chopped
active PWM signals can be required for the high-side drivers
only, the low-side drivers only, or both the high-side and low-
side switches. Therefore, independent control of this mode for
both high-side and low-side switches is included with two
separate control bits in the PWMCFG register.
Typical PWM output signals with high frequency chopping
enabled on both high-side and low-side signals are shown in
Figure 72. Chopping of the high-side PWM outputs (0H, 1H,
and 2H) is enabled by setting Bit 8 of the PWMCFG register.
Chopping of the low-side PWM outputs (0L, 1L, and 2L) is
enabled by setting Bit 9 of the PWMCFG register. The high
chopping frequency is controlled by the 8-bit word (GDCLK)
placed in Bit 0 to Bit 7 of the PWMCFG register. The period of
this high frequency carrier is
tCHOP = (4 × (GDCLK + 1)) × tCORE
The chopping frequency is, therefore, an integral subdivision of
the MicroConverter core frequency
fCHOP = fCORE/(4 × (GDCLK + 1))
相关PDF资料 |
PDF描述 |
|---|---|
| VI-J30-IW-F1 | CONVERTER MOD DC/DC 5V 100W |
| ADUC7021BCPZ62I-RL | IC MCU 12BIT 1MSPS I2C 40-LFCSP |
| VI-B3X-IX-F4 | CONVERTER MOD DC/DC 5.2V 75W |
| VE-BTJ-IX | CONVERTER MOD DC/DC 36V 75W |
| VE-BTH-IX | CONVERTER MOD DC/DC 52V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC7021BCPZ62-RL7 | 功能描述:IC MCU 12BIT 1MSPS UART 40-LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC7xxx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC7022 | 制造商:AD 制造商全称:Analog Devices 功能描述:Precision Analog Microcontroller 12-bit Analog I/O, ARM7TDMI MCU |
| ADUC7022ACP32 | 制造商:Analog Devices 功能描述:FLASH ARM7+10-CH,12-B ADC IC - Trays |
| ADUC7022ACPZ32 | 制造商:Analog Devices 功能描述:MCU 32BIT RISC 32KB FLASH 3.3V 40LFCSP EP - Trays |
| ADUC7022BCP32 | 制造商:Analog Devices 功能描述:FLASH ARM7+10-CH,12-B ADC IC - Trays |
发布紧急采购，3分钟左右您将得到回复。