参数资料
| 型号： | ADUC816BCP |
| 厂商： | Analog Devices Inc |
| 文件页数： | 41/68页 |
| 文件大小： | 0K |
| 描述： | IC MCU 8K FLASH ADC/DAC 56LFCSP |
| 标准包装： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心处理器： | 8052 |
| 芯体尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | PSM，温度传感器，WDT |
| 输入/输出数： | 34 |
| 程序存储器容量： | 8KB（8K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 640 x 8 |
| RAM 容量： | 256 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 数据转换器： | A/D 7x16b; D/A 1x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 56-VFQFN 裸露焊盘，CSP |
| 包装： | 托盘 |
| 产品目录页面： | 738 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
REV. 0
ADuC816
–46–
WDCON
Watchdog Timer Control Register
SFR Address
C0H
Power-On Default Value
10H
Bit Addressable
Yes
3
E
R
P2
E
R
P1
E
R
P0
E
R
PR
I
D
WS
D
WE
D
WR
W
D
W
Table XVII. WDCON SFR Bit Designations
Bit
Name
Description
7
PRE3
Watchdog Timer Prescale Bits.
6
PRE2
The Watchdog timeout period is given by the equation: tWD = (2
PRE
× (29/fPLL))
5
PRE1
(0
≤ PRE ≤ 7; f
PLL = 32.768 kHz)
4
PRE0
PRE3
PRE2
PRE1
PRE0 Timout Period (ms)
Action
0
15.6
Reset or Interrupt
0
1
31.2
Reset or Interrupt
0
1
0
62.5
Reset or Interrupt
0
1
125
Reset or Interrupt
0
1
0
250
Reset or Interrupt
0
1
0
1
500
Reset or Interrupt
0
1
0
1000
Reset or Interrupt
0
1
2000
Reset or Interrupt
1
0
0.0
Immediate Reset
PRE3–0 > 1001
Reserved
3
WDIR
Watchdog Interrupt Response Enable Bit.
If this bit is set by the user, the watchdog will generate an interrupt response instead of a system
reset when the watchdog timeout period has expired. This interrupt is not disabled by the CLR
EA instruction and it is also a fixed, high-priority interrupt. If the watchdog is not being used to
monitor the system, it can alternatively be used as a timer. The prescaler is used to set the timeout
period in which an interrupt will be generated. (See also Note 1, Table XXXIV in the Interrupt
System section.)
2
WDS
Watchdog Status Bit.
Set by the Watchdog Controller to indicate that a watchdog timeout has occurred.
Cleared by writing a “0” or by an external hardware reset. It is not cleared by a watchdog reset.
1
WDE
Watchdog Enable Bit.
Set by user to enable the watchdog and clear its counters. If this bit is not set by the user within
the watchdog timeout period, the watchdog will generate a reset or interrupt, depending on WDIR.
Cleared under the following conditions, User writes “0,” Watchdog Reset (WDIR = “0”);
Hardware Reset; PSM Interrupt.
0
WDWR
Watchdog Write Enable Bit.
To write data into the WDCON SFR involves a double instruction sequence. The WDWR bit must
be set and the very next instruction must be a write instruction to the WDCON SFR.
e.g.,
CLR
EA
;
disable interrupts while writing
to WDT
SETB
WDWR
;
allow write to WDCON
MOV
WDCON, #72h
;
enable WDT for 2.0s timeout
SET B
EA
;
enable interrupts again (if rqd)
Watchdog Timer
The purpose of the watchdog timer is to generate a device reset or
interrupt within a reasonable amount of time if the ADuC816
enters an erroneous state, possibly due to a programming error,
electrical noise, or RFI. The Watchdog function can be disabled by
clearing the WDE (Watchdog Enable) bit in the Watchdog Control
(WDCON) SFR. When enabled; the watchdog circuit will generate
a system reset or interrupt (WDS) if the user program fails to set
the watchdog (WDE) bit within a predetermined amount of time
(see PRE3–0 bits in WDCON). The watchdog timer itself is a
16-bit counter that is clocked at 32.768 kHz. The watchdog
time-out interval can be adjusted via the PRE3–0 bits in WDCON.
Full Control and Status of the watchdog timer function can be
controlled via the watchdog timer control SFR (WDCON). The
WDCON SFR can only be written by user software if the double
write sequence described in WDWR below is initiated on every
write access to the WDCON SFR.
REV. A
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC824BSZ-REEL | IC MCU 8K FLASH ADC/DAC 52MQFP |
| ADUC831BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC832BSZ-REEL | IC MCU 62K FLASH ADC/DAC 52MQFP |
| ADUC834BCPZ-REEL | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC836BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC816BCP-REEL | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 56-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:MCU 8BIT CISC 8KB FLASH 3.3V/5V 56LFCSP EP - Tape and Reel |
| ADUC816BCPZ | 功能描述:IC MCU FLASH 16BIT ADC 56LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC816BCPZ-REEL | 功能描述:8052 MicroConverter? ADuC8xx Microcontroller IC 8-Bit 12.58MHz 8KB (8K x 8) FLASH 56-LFCSP (8x8) 制造商:analog devices inc. 系列:MicroConverter? ADuC8xx 包装:带卷（TR） 零件状态:上次购买时间 核心处理器:8052 核心尺寸:8-位 速度:12.58MHz 连接性:I2C，SPI，UART/USART 外设:PSM，温度传感器，WDT I/O 数:34 程序存储容量:8KB（8K x 8） 程序存储器类型:闪存 EEPROM 容量:640 x 8 RAM 容量:256 x 8 电压 - 电源（Vcc/Vdd）:2.7 V ~ 5.5 V 数据转换器:A/D 7x16b；D/A 1x12b 振荡器类型:内部 工作温度:-40°C ~ 85°C（TA） 封装/外壳:56-WFQFN 裸焊盘，CSP 供应商器件封装:56-LFCSP (8x8) 标准包装:1 |
| ADUC816BS | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 8KB FLASH 12.58MHZ 3.3/5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:8BIT MCU +16BIT ADC MQFP52 816 |
| ADUC816BS-REEL | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 52-Pin MQFP T/R |
发布紧急采购，3分钟左右您将得到回复。