参数资料
| 型号： | ADUC816BCP |
| 厂商： | Analog Devices Inc |
| 文件页数： | 55/68页 |
| 文件大小： | 0K |
| 描述： | IC MCU 8K FLASH ADC/DAC 56LFCSP |
| 标准包装： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心处理器： | 8052 |
| 芯体尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | PSM，温度传感器，WDT |
| 输入/输出数： | 34 |
| 程序存储器容量： | 8KB（8K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 640 x 8 |
| RAM 容量： | 256 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 数据转换器： | A/D 7x16b; D/A 1x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 56-VFQFN 裸露焊盘，CSP |
| 包装： | 托盘 |
| 产品目录页面： | 738 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页当前第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
REV. 0
ADuC816
–59–
Timer 1 Generated Baud Rates
When Timer 1 is used as the baud rate generator, the baud rates
in Modes 1 and 3 are determined by the Timer 1 overflow rate and
the value of SMOD as follows:
Modes 1 and 3 Baud Rate = (2
SMOD/32)
× (Timer 1 Overflow Rate)
The Timer 1 interrupt should be disabled in this application. The
Timer itself can be configured for either timer or counter opera-
tion, and in any of its three running modes. In the most typical
application, it is configured for timer operation, in the autoreload
mode (high nibble of TMOD = 0100Binary). In that case, the baud
rate is given by the formula:
Modes 1 and 3 Baud Rate =
(2
SMOD/32)
× (Core Clock/(12 × [256-TH1]))
A very low baud rate can also be achieved with Timer 1 by leaving
the Timer 1 interrupt enabled, and configuring the timer to run
as a 16-bit timer (high nibble of TMOD = 0100Binary), and using
the Timer 1 interrupt to do a 16-bit software reload. Table XXVIII
below, shows some commonly-used baud rates and how they
might be calculated from a core clock frequency of 1.5728 MHz
and 12.58 MHz. Generally speaking, a 5% error is tolerable
using asynchronous (start/stop) communications.
Table XXVIII. Commonly-Used Baud Rates, Timer 1
Ideal
Core
SMOD
TH1-Reload
Actual
%
Baud
CLK
Value
Baud
Error
9600
12.58
1
–7 (F9h)
9362
2.5
2400
12.58
1
–27 (E5h)
2427
1.1
1200
12.58
1
–55 (C9h)
1192
0.7
1200
1.57
1
–7 (F9h)
1170
2.5
Timer 2 Generated Baud Rates
Baud rates can also be generated using Timer 2. Using Timer 2
is similar to using Timer 1 in that the timer must overflow 16 times
before a bit is transmitted/received. Because Timer 2 has a 16-bit
autoreload mode a wider range of baud rates is possible using
Timer 2.
Modes 1 and 3 Baud Rate = (1/16)
× (Timer 2 Overflow Rate)
Therefore, when Timer 2 is used to generate baud rates, the timer
increments every two clock cycles and not every core machine
cycle as before. Hence, it increments six times faster than Timer
1, and therefore baud rates six times faster are possible. Because
Timer 2 has 16-bit autoreload capability, very low baud rates
are still possible.
Timer 2 is selected as the baud rate generator by setting the TCLK
and/or RCLK in T2CON. The baud rates for transmit and receive
can be simultaneously different. Setting RCLK and/or TCLK puts
Timer 2 into its baud rate generator mode as shown in Figure 41.
In this case, the baud rate is given by the formula:
Modes 1 and 3 Baud Rate
= (Core Clk)/(32
× [65536 – (RCAP2H, RCAP2L)])
Table XXIX shows some commonly used baud rates and how they
might be calculated from a core clock frequency of 1.5728 MHz
and 12.5829 MHz.
Table XXIX. Commonly Used Baud Rates, Timer 2
Ideal
Core
RCAP2H
RCAP2L
Actual
%
Baud
CLK
Value
Baud
Error
19200
12.58
–1 (FFh)
–20 (ECh)
19661
2.4
9600
12.58
–1 (FFh)
–41 (D7h)
9591
0.1
2400
12.58
–1 (FFh)
–164 (5Ch)
2398
0.1
1200
12.58
–2 (FEh)
–72 (B8h)
1199
0.1
9600
1.57
–1 (FFh)
–5 (FBh)
9830
2.4
2400
1.57
–1 (FFh)
–20 (ECh)
2457
2.4
1200
1.57
–1 (FFh)
–41 (D7h)
1199
0.1
CORE
CLK*
2
T2
PIN
TR2
CONTROL
TL2
(8 BITS)
TH2
(8 BITS)
RELOAD
EXEN2
CONTROL
T2EX
PIN
RCAP2L
RCAP2H
NOTE: OSC. FREQ. IS DIVIDED BY 2, NOT 12.
TIMER 2
OVERFLOW
2
16
RCLK
TCLK
RX
CLOCK
TX
CLOCK
0
1
0
SMOD
TIMER 1
OVERFLOW
TRANSITION
DETECTOR
EXF
2
TIMER 2
INTERRUPT
NOTE AVAILABILITY OF ADDITIONAL
EXTERNAL INTERRUPT
C/
T2 = 0
C/
T2 = 1
*THE CORE CLOCK IS THE OUTPUT OF THE PLL AS DESCRIBED ON PAGE 42.
Figure 41. Timer 2, UART Baud Rates
REV. A
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC824BSZ-REEL | IC MCU 8K FLASH ADC/DAC 52MQFP |
| ADUC831BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC832BSZ-REEL | IC MCU 62K FLASH ADC/DAC 52MQFP |
| ADUC834BCPZ-REEL | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC836BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC816BCP-REEL | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 56-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:MCU 8BIT CISC 8KB FLASH 3.3V/5V 56LFCSP EP - Tape and Reel |
| ADUC816BCPZ | 功能描述:IC MCU FLASH 16BIT ADC 56LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC816BCPZ-REEL | 功能描述:8052 MicroConverter? ADuC8xx Microcontroller IC 8-Bit 12.58MHz 8KB (8K x 8) FLASH 56-LFCSP (8x8) 制造商:analog devices inc. 系列:MicroConverter? ADuC8xx 包装:带卷（TR） 零件状态:上次购买时间 核心处理器:8052 核心尺寸:8-位 速度:12.58MHz 连接性:I2C，SPI，UART/USART 外设:PSM，温度传感器，WDT I/O 数:34 程序存储容量:8KB（8K x 8） 程序存储器类型:闪存 EEPROM 容量:640 x 8 RAM 容量:256 x 8 电压 - 电源（Vcc/Vdd）:2.7 V ~ 5.5 V 数据转换器:A/D 7x16b；D/A 1x12b 振荡器类型:内部 工作温度:-40°C ~ 85°C（TA） 封装/外壳:56-WFQFN 裸焊盘，CSP 供应商器件封装:56-LFCSP (8x8) 标准包装:1 |
| ADUC816BS | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 8KB FLASH 12.58MHZ 3.3/5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:8BIT MCU +16BIT ADC MQFP52 816 |
| ADUC816BS-REEL | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 52-Pin MQFP T/R |
发布紧急采购，3分钟左右您将得到回复。