参数资料
| 型号： | ADUC816BCP |
| 厂商： | Analog Devices Inc |
| 文件页数： | 44/68页 |
| 文件大小： | 0K |
| 描述： | IC MCU 8K FLASH ADC/DAC 56LFCSP |
| 标准包装： | 1 |
| 系列： | MicroConverter® ADuC8xx |
| 核心处理器： | 8052 |
| 芯体尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | PSM，温度传感器，WDT |
| 输入/输出数： | 34 |
| 程序存储器容量： | 8KB（8K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 640 x 8 |
| RAM 容量： | 256 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 5.5 V |
| 数据转换器： | A/D 7x16b; D/A 1x12b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 56-VFQFN 裸露焊盘，CSP |
| 包装： | 托盘 |
| 产品目录页面： | 738 (CN2011-ZH PDF) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页当前第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
REV. 0
ADuC816
–49–
Table XIX. SPICON SFR Bit Designations (continued)
Bit
Name
Description
1
SPR1
SPI Bit-Rate Select Bits.
0
SPR0
These bits select the SCLOCK rate (bit-rate) in Master Mode as follows:
SPR1
SPR0
Selected Bit Rate
00fCORE/2
01fCORE/4
10fCORE/8
11fCORE/16
In SPI Slave Mode, i.e., SPIM = 0, the logic level on the external
SS pin (Pin 13), can be read
via the SPR0 bit.
NOTE
The CPOL and CPHA bits should both contain the same values for master and slave devices.
SPIDAT
SPI Data Register
Function
The SPIDAT SFR is written by the user to transmit data over the SPI interface or read by user
code to read data just received by the SPI interface.
SFR Address
F7H
Power-On Default Value
00H
Bit Addressable
No
Using the SPI Interface
Depending on the configuration of the bits in the SPICON SFR
shown in Table XIX, the ADuC816 SPI interface will transmit
or receive data in a number of possible modes. Figure 32 shows
all possible ADuC816 SPI configurations and the timing rela-
tionships and synchronization between the signals involved.
Also shown in this figure is the SPI interrupt bit (ISPI) and how
it is triggered at the end of each byte-wide communication.
SCLOCK
(CPOL = 1)
SCLOCK
(CPOL = 0)
(CPHA = 1)
(CPHA = 0)
SAMPLE INPUT
ISPI FLAG
DATA OUTPUT
ISPI FLAG
SAMPLE INPUT
DATA OUTPUT
?
MSB
BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB
SS
MSB BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 LSB
Figure 32. SPI Timing, All Modes
SPI Interface—Master Mode
In master mode, the SCLOCK pin is always an output and gener-
ates a burst of eight clocks whenever user code writes to the
SPIDAT register. The SCLOCK bit rate is determined by
SPR0 and SPR1 in SPICON. It should also be noted that the
SS pin is not used in master mode. If the ADuC816 needs to
assert the
SS pin on an external slave device, a Port digital output
pin should be used.
In master mode a byte transmission or reception is initiated
by a write to SPIDAT. Eight clock periods are generated via the
SCLOCK pin and the SPIDAT byte being transmitted via MOSI.
With each SCLOCK period a data bit is also sampled via MISO.
After eight clocks, the transmitted byte will have been completely
transmitted and the input byte will be waiting in the input shift
register. The ISPI flag will be set automatically and an interrupt
will occur if enabled. The value in the shift register will be latched
into SPIDAT.
SPI Interface—Slave Mode
In slave mode the SCLOCK is an input. The
SS pin must
also be driven low externally during the byte communication.
Transmission is also initiated by a write to SPIDAT. In slave
mode, a data bit is transmitted via MISO and a data bit is received
via MOSI through each input SCLOCK period. After eight clocks,
the transmitted byte will have been completely transmitted and the
input byte will be waiting in the input shift register. The ISPI flag
will be set automatically and an interrupt will occur if enabled.
The value in the shift register will be latched into SPIDAT only
when the transmission/reception of a byte has been completed.
The end of transmission occurs after the eighth clock has been
received, if CPHA = 1 or when
SS returns high if CPHA = 0.
REV. A
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC824BSZ-REEL | IC MCU 8K FLASH ADC/DAC 52MQFP |
| ADUC831BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC832BSZ-REEL | IC MCU 62K FLASH ADC/DAC 52MQFP |
| ADUC834BCPZ-REEL | IC MCU 62K FLASH ADC/DAC 56LFCSP |
| ADUC836BCPZ | IC MCU 62K FLASH ADC/DAC 56LFCSP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC816BCP-REEL | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 56-Pin LFCSP EP T/R 制造商:Analog Devices 功能描述:MCU 8BIT CISC 8KB FLASH 3.3V/5V 56LFCSP EP - Tape and Reel |
| ADUC816BCPZ | 功能描述:IC MCU FLASH 16BIT ADC 56LFCSP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:38 系列:Encore!® XP® 核心处理器:eZ8 芯体尺寸:8-位 速度:5MHz 连通性:IrDA，UART/USART 外围设备:欠压检测/复位，LED，POR，PWM，WDT 输入/输出数:16 程序存储器容量:4KB（4K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 3.6 V 数据转换器:- 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:20-SOIC（0.295"，7.50mm 宽） 包装:管件 其它名称:269-4116Z8F0413SH005EG-ND |
| ADUC816BCPZ-REEL | 功能描述:8052 MicroConverter? ADuC8xx Microcontroller IC 8-Bit 12.58MHz 8KB (8K x 8) FLASH 56-LFCSP (8x8) 制造商:analog devices inc. 系列:MicroConverter? ADuC8xx 包装:带卷（TR） 零件状态:上次购买时间 核心处理器:8052 核心尺寸:8-位 速度:12.58MHz 连接性:I2C，SPI，UART/USART 外设:PSM，温度传感器，WDT I/O 数:34 程序存储容量:8KB（8K x 8） 程序存储器类型:闪存 EEPROM 容量:640 x 8 RAM 容量:256 x 8 电压 - 电源（Vcc/Vdd）:2.7 V ~ 5.5 V 数据转换器:A/D 7x16b；D/A 1x12b 振荡器类型:内部 工作温度:-40°C ~ 85°C（TA） 封装/外壳:56-WFQFN 裸焊盘，CSP 供应商器件封装:56-LFCSP (8x8) 标准包装:1 |
| ADUC816BS | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 52-Pin MQFP 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 8KB FLASH 12.58MHZ 3.3/5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:8BIT MCU +16BIT ADC MQFP52 816 |
| ADUC816BS-REEL | 制造商:Analog Devices 功能描述:MCU 8-Bit ADuC8xx 8052 CISC 8KB Flash 3.3V/5V 52-Pin MQFP T/R |
发布紧急采购，3分钟左右您将得到回复。