- 您现在的位置：买卖IC网 > PDF目录11203 > ADUC848BSZ8-3 (Analog Devices Inc)IC MCU FLASH W/16BIT ADC 52MQFP PDF资料下载
参数资料
| 型号： | ADUC848BSZ8-3 |
| 厂商： | Analog Devices Inc |
| 文件页数： | 89/108页 |
| 文件大小： | 0K |
| 描述： | IC MCU FLASH W/16BIT ADC 52MQFP |
| 标准包装： | 96 |
| 系列： | MicroConverter® ADuC8xx |
| 核心处理器： | 8052 |
| 芯体尺寸： | 8-位 |
| 速度： | 12.58MHz |
| 连通性： | I²C，SPI，UART/USART |
| 外围设备： | POR，PSM，PWM，温度传感器，WDT |
| 输入/输出数： | 34 |
| 程序存储器容量： | 8KB（8K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 4K x 8 |
| RAM 容量： | 2.25K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 3.6 V |
| 数据转换器： | A/D 10x16b; D/A 1x12b，2x16b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | 52-QFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页当前第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页
Data Sheet
ADuC845/ADuC847/ADuC848
Rev. C | Page 81 of 108
Mode 0 (8-Bit Shift Register Mode)
Mode 0 is selected by clearing both the SM0 and SM1 bits in
the SFR SCON. Serial data enters and exits through RxD. TxD
outputs the shift clock. Eight data bits are transmitted or
received. Transmission is initiated by any instruction that writes
to SBUF. The data is shifted out of the RxD line. The 8 bits are
transmitted with the least significant bit (LSB) first.
Reception is initiated when the receive enable bit (REN) is 1
and the receive interrupt bit (RI) is 0. When RI is cleared, the
data is clocked into the RxD line, and the clock pulses are
output from the TxD line as shown in Figure 58.
RxD
(DATA OUT)
TxD
(SHIFT CLOCK)
DATA BIT 0
DATA BIT 1
DATA BIT 6
DATA BIT 7
04741-055
Figure 58. 8-Bit Shift Register Mode
Mode 1 (8-Bit UART, Variable Baud Rate)
Mode 1 is selected by clearing SM0 and setting SM1. Each data
byte (LSB first) is preceded by a start bit (0) and followed by a
stop bit (1). Therefore, 10 bits are transmitted on TxD or are
received on RxD. The baud rate is set by the Timer 1 or Timer 2
overflow rate, or a combination of the two (one for transmission
and the other for reception).
Transmission is initiated by writing to SBUF. The write to SBUF
signal also loads a 1 (stop bit) into the 9th bit position of the
transmit shift register. The data is output bit-by-bit until the
stop bit appears on TxD and the transmit interrupt flag (TI) is
automatically set as shown in Figure 59.
TxD
TI
(SCON.1)
START
BIT
D0
D1
D2
D3
D4
D5
D6
D7
STOP BIT
SET INTERRUPT
I.E., READY FOR MORE DATA
04741-056
Figure 59. 8-Bit Variable Baud Rate
Reception is initiated when a 1-to-0 transition is detected on
RxD. Assuming that a valid start bit is detected, character
reception continues. The start bit is skipped and the 8 data bits
are clocked into the serial port shift register. When all 8 bits
have been clocked in, the following events occur:
The 8 bits in the receive shift register are latched into SBUF.
The 9th bit (stop bit) is clocked into RB8 in SCON.
The receiver interrupt flag (RI) is set.
All of the following conditions must be met at the time the final
shift pulse is generated:
RI = 0
Either SM2 = 0 or SM2 = 1
Received stop bit = 1
If any of these conditions is not met, the received frame is
irretrievably lost, and RI is not set.
Mode 2 (9-Bit UART with Fixed Baud Rate)
Mode 2 is selected by setting SM0 and clearing SM1. In this
mode, the UART operates in 9-bit mode with a fixed baud rate.
The baud rate is fixed at Core_Clk/64 by default, although by
setting the SMOD bit in PCON, the frequency can be doubled
to Core_Clk/32. Eleven bits are transmitted or received: a start
bit (0), 8 data bits, a programmable 9th bit, and a stop bit (1).
The 9th bit is most often used as a parity bit, although it can be
used for anything, including a ninth data bit if required.
To transmit, the 8 data bits must be written into SBUF. The
ninth bit must be written to TB8 in SCON. When transmission
is initiated, the 8 data bits (from SBUF) are loaded into the
transmit shift register (LSB first). The contents of TB8 are
loaded into the 9th bit position of the transmit shift register.
The transmission starts at the next valid baud rate clock. The
TI flag is set as soon as the stop bit appears on TxD.
Reception for Mode 2 is similar to that of Mode 1. The 8 data
bytes are input at RxD (LSB first) and loaded onto the receive
shift register. When all 8 bits have been clocked in, the
following events occur:
The 8 bits in the receive shift register are latched into SBUF.
The 9th data bit is latched into RB8 in SCON.
The receiver interrupt flag (RI) is set.
All of the following conditions must be met at the time the final
shift pulse is generated:
RI = 0
Either SM2 = 0 or SM2 = 1
Received stop bit = 1
If any of these conditions is not met, the received frame is
irretrievably lost, and RI is not set.
相关PDF资料 |
PDF描述 |
|---|---|
| ADUC7020BCPZ62I-RL | IC MCU 12BIT 1MSPS I2C 40-LFCSP |
| ATXMEGA256A3B-MHR | IC MCU 8BIT 256KB FLASH 64VQFN |
| ATXMEGA256A3B-AUR | IC MCU 8BIT 256KB FLASH 64TQFP |
| VE-B33-IX-F2 | CONVERTER MOD DC/DC 24V 75W |
| VE-B33-IW-F4 | CONVERTER MOD DC/DC 24V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ADUC848BSZ8-5 | 功能描述:IC MCU FLASH W/16BIT ADC 52MQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:MicroConverter® ADuC8xx 标准包装:250 系列:LPC11Uxx 核心处理器:ARM? Cortex?-M0 芯体尺寸:32-位 速度:50MHz 连通性:I²C，Microwire，SPI，SSI，SSP，UART/USART，USB 外围设备:欠压检测/复位，POR，WDT 输入/输出数:40 程序存储器容量:96KB（96K x 8） 程序存储器类型:闪存 EEPROM 大小:4K x 8 RAM 容量:10K x 8 电压 - 电源 (Vcc/Vdd):1.8 V ~ 3.6 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:48-LQFP 包装:托盘 其它名称:568-9587 |
| AD-UCFS-JRN-SPRD | 功能描述:PRD LIC UCFS JOURNAL CCES 1 PRD RoHS:否 类别:编程器，开发系统 >> 软件 系列:* 标准包装:1 系列:ISE® 设计套件 类型:订阅 适用于相关产品:Xilinx FPGAs 其它名称:Q4986209T1081384 |
| AD-UCFS-MJRN-SP | 功能描述:PRD LIC UCFS JOURNAL MAIN 1 PRD RoHS:否 类别:编程器，开发系统 >> 软件 系列:* 标准包装:1 系列:ISE® 设计套件 类型:订阅 适用于相关产品:Xilinx FPGAs 其它名称:Q4986209T1081384 |
| AD-UCFS-MNT-SP | 功能描述:PRD LIC UCFS CORE MAIN 1 PRD RoHS:否 类别:编程器，开发系统 >> 软件 系列:* 标准包装:1 系列:ISE® 设计套件 类型:订阅 适用于相关产品:Xilinx FPGAs 其它名称:Q4986209T1081384 |
| AD-UCFS-SPRD | 功能描述:PRD LIC UCFS CORE CCES 1 PROD RoHS:否 类别:编程器，开发系统 >> 软件 系列:* 标准包装:1 系列:ISE® 设计套件 类型:订阅 适用于相关产品:Xilinx FPGAs 其它名称:Q4986209T1081384 |
发布紧急采购，3分钟左右您将得到回复。