- 您现在的位置：买卖IC网 > PDF目录295065 > AM29DL162CB120ZEN (SPANSION LLC) 1M X 16 FLASH 3V PROM, 120 ns, PDSO56 PDF资料下载
参数资料
| 型号： | AM29DL162CB120ZEN |
| 厂商： | SPANSION LLC |
| 元件分类： | PROM |
| 英文描述： | 1M X 16 FLASH 3V PROM, 120 ns, PDSO56 |
| 封装： | SSOP-56 |
| 文件页数： | 24/55页 |
| 文件大小： | 775K |
| 代理商： | AM29DL162CB120ZEN |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页
28
Am29DL16xC
September 7, 2007 21533C2
D A TA
SH EE T
WRITE OPERATION STATUS
The device provides several bits to determine the status of a
program or erase operation: DQ2, DQ3, DQ5, DQ6, and
DQ7. Table 15 and the following subsections describe the
function of these bits. DQ7 and DQ6 each offer a method for
determining whether a program or erase operation is com-
plete or in progress. The device also provides a hard-
ware-based output signal, RY/BY#, to determine whether
an Embedded Program or Erase operation is in progress or
has been completed.
DQ7: Data# Polling
The Data# Polling bit, DQ7, indicates to the host system
whether an Embedded Program or Erase algorithm is in
progress or completed, or whether a bank is in Erase Sus-
pend. Data# Polling is valid after the rising edge of the final
WE# pulse in the command sequence.
During the Embedded Program algorithm, the device out-
puts on DQ7 the complement of the datum programmed to
DQ7. This DQ7 status also applies to programming during
Erase Suspend. When the Embedded Program algorithm is
complete, the device outputs the datum programmed to
DQ7. The system must provide the program address to
read valid status information on DQ7. If a program address
falls within a protected sector, Data# Polling on DQ7 is ac-
tive for approximately 1 s, then that bank returns to reading
array data.
During the Embedded Erase algorithm, Data# Polling
produces a “0” on DQ7. When the Embedded Erase
algorithm is complete, or if the bank enters the Erase
Suspend mode, Data# Polling produces a “1” on DQ7.
The system must provide an address within any of the
sectors selected for erasure to read valid status infor-
mation on DQ7.
After an erase command sequence is written, if all
sectors selected for erasing are protected, Data# Poll-
ing on DQ7 is active for approximately 100 s, then the
bank returns to reading array data. If not all selected
sectors are protected, the Embedded Erase algorithm
erases the unprotected sectors, and ignores the se-
lected sectors that are protected. However, if the sys-
tem reads DQ7 at an address within a protected
sector, the status may not be valid.
Just prior to the completion of an Embedded Program
or Erase operation, DQ7 may change asynchronously
with DQ0–DQ6 while Output Enable (OE#) is asserted
low. That is, the device may change from providing
status information to valid data on DQ7. Depending on
when the system samples the DQ7 output, it may read
the status or valid data. Even if the device has com-
pleted the program or erase operation and DQ7 has
valid data, the data outputs on DQ0–DQ6 may be still
invalid. Valid data on DQ0–DQ7 will appear on suc-
cessive read cycles.
Table 15 shows the outputs for Data# Polling on DQ7.
in the AC Characteristics section shows the Data#
Polling timing diagram.
Figure 5.
Data# Polling Algorithm
DQ7 = Data?
Yes
No
DQ5 = 1?
No
Yes
FAIL
PASS
Read DQ7–DQ0
Addr = VA
Read DQ7–DQ0
Addr = VA
DQ7 = Data?
START
Notes:
1. VA = Valid address for programming. During a sector
erase operation, a valid address is any sector address
within the sector being erased. During chip erase, a
valid address is any non-protected sector address.
2. DQ7 should be rechecked even if DQ5 = “1” because
DQ7 may change simultaneously with DQ5.
相关PDF资料 |
PDF描述 |
|---|---|
| AM29DL163CT70ZC | 1M X 16 FLASH 3V PROM, 70 ns, PDSO56 |
| AM29DL163CT70RZI | 1M X 16 FLASH 3V PROM, 70 ns, PDSO56 |
| AM29F040B-150JEB | 4 Megabit (512 K x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| AM29F040B-150JIB | 4 Megabit (512 K x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
| AM29F040B-150PCB | 4 Megabit (512 K x 8-Bit) CMOS 5.0 Volt-only, Uniform Sector Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AM29DL163DB-90EI\\T | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 16MBIT 2MX8/1MX16 90NS 48TSOP - Tape and Reel |
| AM29DL163DB-90EI\T | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 16MBIT 2MX8/1MX16 90NS 48TSOP - Tape and Reel |
| AM29DL163DB-90EIT | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 16MBIT 2MX8/1MX16 90NS 48TSOP - Tape and Reel |
| AM29DL163DT70EF | 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 16MBIT 2MX8/1MX16 70NS 48TSOP - Trays |
| AM29DL163DT-70EF | 制造商:Spansion 功能描述: |
发布紧急采购，3分钟左右您将得到回复。