- 您现在的位置：买卖IC网 > PDF目录16616 > AT73C224-A (Atmel)IC PWR MGMT ANALOG PMAAC 32QFN PDF资料下载
参数资料
| 型号： | AT73C224-A |
| 厂商： | Atmel |
| 文件页数： | 10/75页 |
| 文件大小： | 0K |
| 描述： | IC PWR MGMT ANALOG PMAAC 32QFN |
| 标准包装： | 490 |
| 应用： | 手持/移动设备 |
| 电源电压： | 2.8 V ~ 5.25 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN（5x5） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页当前第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页
5.2
5.2.1
5.2.2
5.2.2.1
5.2.2.2
10
Automatic Start-up Sequences and Shut-down
Start-up/Wakeup
If the backup battery (only) is present, the RTC is running (1.2 μA). This mode is called “Backup
mode”. When the main battery is plugged in and voltage is higher than 2.8V, the LDO_RTC
recharges the backup battery through an internal switch (if the main battery is lower than 2.8V,
nothing happens, RTC still running). This mode is called “Standby mode”. Note that when the
battery is plugged in (and higher than 2.8V), a reset of the RTC is performed only if the backup
battery was lower than 1.8V.
Now, the system waits for wake-up information coming from the pushbutton (EN pin) or an RTC
alarm. When one of the previous conditions occurs, the automatic start-up sequence starts
(without any external commands).
Different automatic start-up sequences can be chosen from the AT73C224-x family (see Figure
When the automatic start-up sequence has been completed, the POK signal (which is an open
drain signal) goes high, thus implementing a sort of POR for the user (i.e., a microcontroller) and
enters into “Normal mode”.
Note: Power On is controlled by default by an external pushbutton, connected on EN pin (the EN
pad has an internal 100 k ? pull up). A switch can also be used as shown bellow but should be a
request from the customer
.
EN
(Default: Pushbutton)
EN
(On request: switch)
Shut-down
Static Mode
In Static mode, the Power-off condition is an OR between the following conditions: main battery
lower than 2.8V or electrical default in the DC/DC (short-circuit). When Power-off condition
occurs, POK signal is cleared, then the AT73C224-x device waits for the signal ITB/RDY to shut
down all power supplies.
Dynamic Mode
In Dynamic mode, Power-off condition is an OR between the following conditions: electrical
default in the DC/DC (short-circuit) or software shutdown. When main battery lower than 2.8V,
an interrupt is generated on signal ITB/RDY. It is the responsibility of the host microcontroller to
perform a software shut-down by properly writing the AT73C224-x device registers through the
serial interface. After that, the POK signal is cleared, and all is turned off. A check on the push-
button is then performed to assure that it has been released, thus avoiding continuous on-off-on
behavior. The “normal” shutdown is performed by software. Note that the microcontroller has to
write the proper register to enable the power off (see Section 6. ”Register Tables” ).
AT73C224
6266A–PMAAC–08-Sep-08
相关PDF资料 |
PDF描述 |
|---|---|
| GSC10DRYH | CONN EDGECARD 20POS DIP .100 SLD |
| VLCF4028T-330MR61-2 | INDUCTOR POWER 33UH .61A SMD |
| HBM22DRUN | CONN EDGECARD 44POS .156 DIP SLD |
| A1AXH-2436M | IDC CABLE - ASC24H/AE24M/X |
| M1CXA-2636R | IDC CABLE - MKC26A/MC26M/X |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT73C224-B | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Power Management and Analog Companions (PMAAC) |
| AT73C224-C | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Power Management and Analog Companions (PMAAC) |
| AT73C224-D | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Power Management and Analog Companions (PMAAC) |
| AT73C224-E | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Power Management and Analog Companions (PMAAC) |
| AT73C224-EK1 | 功能描述:电源管理IC开发工具 AT73C224 EVALUATION KIT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。