- 您现在的位置：买卖IC网 > PDF目录16616 > AT73C224-A (Atmel)IC PWR MGMT ANALOG PMAAC 32QFN PDF资料下载
参数资料
| 型号： | AT73C224-A |
| 厂商： | Atmel |
| 文件页数： | 14/75页 |
| 文件大小： | 0K |
| 描述： | IC PWR MGMT ANALOG PMAAC 32QFN |
| 标准包装： | 490 |
| 应用： | 手持/移动设备 |
| 电源电压： | 2.8 V ~ 5.25 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 32-VFQFN 裸露焊盘 |
| 供应商设备封装： | 32-QFN（5x5） |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页当前第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页
Figure 5-4.
Configurable Static Mode
D1
D2
D3
D4
ITB/RDY
POK
0
1
Power OK
The state of each channel is determined by the internal state machine during the start-up
sequence. POK is looped back onto ITB/RDY. When this signal changes from 0 to 1 (i.e., the
start-up is completed), the control of each supply channel is passed on to D1-D4. This allows
changing the output values defined by the state machine. This mode can be used when the 4th
channel is needed.
Figure 5-5.
GPIO (μC Controlled)
D1
D2
I/O
I/O
D3
I/O
μC
D4
ITB/RDY
POK
I/O
I/O
RST or NMI
When the system is powered, the microcontroller is not necessarily well configured and may be
unable to drive D1-D4 correctly. Since ITB/RDY is not actively controlled, its state is an unknown
logic level. If ITB/RDY is in hi-Z, the weak internal pullup pulls the level to 1. The power channels
are controlled by the internal state machine. After some initialization time, the microcontroller
configures its GPIOs to drive D1-D4 as wished. At the end of the software configuration, the
microcontroller changes the level of ITB/RDY to 0 in order to get control on the four power chan-
nels through D1-D4.
5.3.2
14
Dynamic Mode
For the devices of the AT73C224-x family that work in dynamic mode, supply management can
be performed by the SPI or TWI digital interface. Selection between the two digital interfaces is
done through D4 pin when the AT73C224-x is enabled. Pin D4 is a digital input pin that features
a controllable pull-up resistor with active low control signal. When the AT73C224-x starts, the
pullup is disabled until a push button event is detected. The state machine enables the pull-up
resistor on D4, waits for a time and then checks back on the value on the pad.
? If D4 is high (i.e., the level externally applied on D4 is HZ or logic 1), SPI interface is selected.
D4 will become SCS.
? If D4 is low (i.e., D4 is externally grounded), TWI interface is selected. D4 is not used.
After signal dynamic has been determined the state machine disables the pull-up resistor to
save power and the D4 pin can be normally used (if SPI has been selected).
AT73C224
6266A–PMAAC–08-Sep-08
相关PDF资料 |
PDF描述 |
|---|---|
| GSC10DRYH | CONN EDGECARD 20POS DIP .100 SLD |
| VLCF4028T-330MR61-2 | INDUCTOR POWER 33UH .61A SMD |
| HBM22DRUN | CONN EDGECARD 44POS .156 DIP SLD |
| A1AXH-2436M | IDC CABLE - ASC24H/AE24M/X |
| M1CXA-2636R | IDC CABLE - MKC26A/MC26M/X |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT73C224-B | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Power Management and Analog Companions (PMAAC) |
| AT73C224-C | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Power Management and Analog Companions (PMAAC) |
| AT73C224-D | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Power Management and Analog Companions (PMAAC) |
| AT73C224-E | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Power Management and Analog Companions (PMAAC) |
| AT73C224-EK1 | 功能描述:电源管理IC开发工具 AT73C224 EVALUATION KIT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
发布紧急采购，3分钟左右您将得到回复。