参数资料
| 型号： | AT89LP428-20AU |
| 厂商： | Atmel |
| 文件页数： | 144/149页 |
| 文件大小： | 0K |
| 描述： | MCU 8051 4K FLASH SPI 32TQFP |
| 产品培训模块： | MCU Product Line Introduction |
| 标准包装： | 250 |
| 系列： | 89LP |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 20MHz |
| 连通性： | SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 30 |
| 程序存储器容量： | 4KB（4K x 8） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 512 x 8 |
| RAM 容量： | 768 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.4 V ~ 5.5 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 32-TQFP |
| 包装： | 托盘 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页当前第144页第145页第146页第147页第148页第149页
94
3654A–MICRO–8/09
AT89LP428/828
While the TXE flag is set, the transmit buffer is empty. TXE can be cleared by software or by
writing to SPDR. Writing to SPDR will clear TXE and load the transmit buffer. The user may load
the buffer while the shift register is busy, i.e. before the current transfer completes. When the
current transfer completes, the queued byte in the transmit buffer is moved to the shift register
and the next transfer commences. TXE will generate an interrupt if the SPI interrupt is enabled
and if the ENH bit in SPSR is set. For multi-byte transfers, TXE may be used to remove any
dead time between byte transmissions.
The SPI master can operate in two modes: multi-master mode and single-master mode. By
default, multi-master mode is active when SSIG = 0. In this mode, the SS input is used to dis-
able a master device when another master is accessing the bus. When SS is driven low, the
master device becomes a slave by clearing its MSTR bit and a Mode Fault is generated by set-
ting the MODF bit in SPSR. MODF will generate an interrupt if enabled. The MSTR bit must be
set in software before the device may become a master again. Single-master mode is enabled
by setting SSIG = 1. In this mode SS is ignored and the master is always active. SS may be
used as a general-purpose I/O in this mode.
17.2
Slave Operation
When the AT89LP428/828 is not configured for master operation, MSTR = 0, it will operate as
an SPI slave. In slave mode, bytes are shifted in through MOSI and out through MISO by a mas-
ter device controlling the serial clock on SCK. When a byte has been transferred, the SPIF flag
is set to “1” and an interrupt request is generated, if enabled. The data received from the
addressed master device is also transferred from the shift register to the receive buffer. The
received data is accessed by reading SPDR. A slave device cannot initiate transfers. Data to be
transferred to the master device must be preloaded by writing to SPDR. Writes to SPDR are
double-buffered. The transmit buffer is loaded first and if the shift register is empty, the contents
of the buffer will be transferred to the shift register.
While the TXE flag is set, the transmit buffer is empty. TXE can be cleared by software or by
writing to SPDR. Writing to SPDR will clear TXE and load the transmit buffer. The user may load
the buffer while the shift register is busy, i.e. before the current transfer completes. When the
current transfer completes, the queued byte in the transmit buffer is moved to the shift register
and waits for the master to initiate another transfer. TXE will generate an interrupt if the SPI
interrupt is enabled and if the ENH bit in SPSR is set.
The SPI slave can operate in two modes: 4-wire mode and 3-wire mode. By default, 4-wire
mode is active when SSIG = 0. In this mode, the SS input is used to enable/disable the slave
device when addressed by a master. When SS is driven low, the slave device is enabled and will
shift out data on MISO in response to the serial clock on SCK. While SS is high, the SPI slave
will remain sleeping with MISO inactive. 3-wire mode is enabled by setting SSIG = 1. In this
mode SS is ignored and the slave is always active. SS may be used as a general-purpose I/O in
this mode.
The Disable Slave Output bit, DISSO in SPSR, may be used to disable the MISO line of a slave
device. DISSO can allow several slave devices to share MISO while operating in 3-wire mode. In
this case some protocol other than SS may be used to determine which slave is enabled.
相关PDF资料 |
PDF描述 |
|---|---|
| AT89LP52-20MU | IC MCU 8051 8K FLASH SPI 44VQFN |
| AT89LP6440-20JU | MCU 8051 64K FLASH ISP 44PLCC |
| AT89LP828-JU | IC MCU 8051 8KB FLASH 32PLCC |
| AT89LS51-16AU | IC MCU 4K FLASH 16MHZ 44-TQFP |
| AT89LS52-16PU | IC MCU 8K FLASH 16MHZ 40-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT89LP428-20JU | 功能描述:8位微控制器 -MCU SingleCycle 8051 4K ISP Flash 2.4V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| AT89LP428-20MH | 功能描述:8位微控制器 -MCU SingleCycle 8051 4K ISP Flash 2.4V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| AT89LP428-20PU | 功能描述:8位微控制器 -MCU SingleCycle 8051 4K ISP Flash 2.4V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| AT89LP51-20AU | 功能描述:8位微控制器 -MCU Single Cycle 8051 4K ISP FL RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| AT89LP51-20JU | 功能描述:8位微控制器 -MCU Single Cycle 8051 4K ISP FL RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
发布紧急采购，3分钟左右您将得到回复。