参数资料
| 型号： | AT90S8535-8PI |
| 厂商： | Atmel |
| 文件页数： | 92/127页 |
| 文件大小： | 0K |
| 描述： | IC MCU 8K FLSH 8MHZ A/D IT 40DIP |
| 标准包装： | 18 |
| 系列： | AVR® 90S |
| 核心处理器： | AVR |
| 芯体尺寸： | 8-位 |
| 速度： | 8MHz |
| 连通性： | SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，PWM，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 8KB（4K x 16） |
| 程序存储器类型： | 闪存 |
| EEPROM 大小： | 512 x 8 |
| RAM 容量： | 512 x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 4 V ~ 6 V |
| 数据转换器： | A/D 8x10b |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 40-DIP（0.600"，15.24mm） |
| 包装： | 管件 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页当前第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页
1997 Microchip Technology Inc.
DS30272A-page 67
PIC16C71X
FIGURE 8-22: WAKE-UP FROM SLEEP THROUGH INTERRUPT
Q1
Q2
Q3 Q4
Q1 Q2
Q3
Q4
Q1
Q2 Q3 Q4
Q1 Q2 Q3 Q4
Q1
Q2 Q3
Q4
Q1 Q2
Q3
Q4
OSC1
CLKOUT(4)
INT pin
INTF ag
(INTCON<1>)
GIE bit
(INTCON<7>)
INSTRUCTION FLOW
PC
Instruction
fetched
Instruction
executed
PC
PC+1
PC+2
Inst(PC) = SLEEP
Inst(PC - 1)
Inst(PC + 1)
SLEEP
Processor in
SLEEP
Interrupt Latency
(Note 2)
Inst(PC + 2)
Inst(PC + 1)
Inst(0004h)
Inst(0005h)
Inst(0004h)
Dummy cycle
PC + 2
0004h
0005h
Dummy cycle
TOST(2)
PC+2
Note
1:
XT, HS or LP oscillator mode assumed.
2:
TOST = 1024TOSC (drawing not to scale) This delay will not be there for RC osc mode.
3:
GIE = '1' assumed. In this case after wake- up, the processor jumps to the interrupt routine. If GIE = '0', execution will continue in-line.
4:
CLKOUT is not available in these osc modes, but shown here for timing reference.
8.9
Program Verication/Code Protection
If the code protection bit(s) have not been pro-
grammed, the on-chip program memory can be read
out for verication purposes.
8.10
ID Locations
Four memory locations (2000h - 2003h) are designated
as ID locations where the user can store checksum or
other code-identication numbers. These locations are
not accessible during normal execution but are read-
able and writable during program/verify. It is recom-
mended that only the 4 least signicant bits of the ID
location are used.
8.11
In-Circuit Serial Programming
PIC16CXX microcontrollers can be serially pro-
grammed while in the end application circuit. This is
simply done with two lines for clock and data, and three
other lines for power, ground, and the programming
voltage. This allows customers to manufacture boards
with unprogrammed devices, and then program the
microcontroller just before shipping the product. This
also allows the most recent rmware or a custom rm-
ware to be programmed.
Note:
Microchip does not recommend code pro-
tecting windowed devices.
The device is placed into a program/verify mode by
holding the RB6 and RB7 pins low while raising the
MCLR (VPP) pin from VIL to VIHH (see programming
specication). RB6 becomes the programming clock
and RB7 becomes the programming data. Both RB6
and RB7 are Schmitt Trigger inputs in this mode.
After reset, to place the device into programming/verify
mode, the program counter (PC) is at location 00h. A 6-
bit command is then supplied to the device. Depending
on the command, 14-bits of program data are then sup-
plied to or from the device, depending if the command
was a load or a read. For complete details of serial pro-
gramming, please refer to the PIC16C6X/7X Program-
ming Specications (Literature #DS30228).
FIGURE 8-23: TYPICAL IN-CIRCUIT SERIAL
PROGRAMMING
CONNECTION
External
Connector
Signals
To Normal
Connections
To Normal
Connections
PIC16CXX
VDD
VSS
MCLR/VPP
RB6
RB7
+5V
0V
VPP
CLK
Data I/O
VDD
相关PDF资料 |
PDF描述 |
|---|---|
| AT90USB1287-16AUR | IC MCU AVR 128K ISP USB TQFP64 |
| AT90USB162-16AUR | IC AVR MCU 16K FLASH 32TQFP |
| AT91FR40162SB-CU-999 | IC MCU 32BIT RISC 121BGA |
| AT91M40800-33AI SL383 | IC ARM MCU 16BIT 100TQFP |
| AT91M42800A-33CJ | IC ARM7 MCU 144 BGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| AT90SA7-MLTU | 功能描述:程序设计器 - 基于通用和内存 ASICS RoHS:否 制造商:Xeltek 产品:Universal Device Programmers 工具用于评估:EPROM, Parallel/Serial EEPROM, FPGA, PROM, Flash, BPROM, MCUs, PLD Devices 接口类型:Parallel, USB 工作电源电压:90 VAC to 250 VAC |
| AT90SC12036RU | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Secure Microcontroller for Smart Cards |
| AT90SC128112RU | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Secure Microcontroller for Smart Cards |
| AT90SC12836RCFT | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Secure Microcontrollers for Smart Cards |
| AT90SC12836RCFT_07 | 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Secure Microcontrollers for Smart Cards |
发布紧急采购，3分钟左右您将得到回复。