参数资料
| 型号： | ATICE10 |
| 厂商： | Atmel |
| 文件页数： | 13/35页 |
| 文件大小： | 0K |
| 描述： | AVR IN CIRCUIT EMULATOR |
| 标准包装： | 1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
Preparing the ICE10 System for Use
2.2
2.3
2.4
2.5
2.6
Connecting
ICE10 to PC
Connecting
ICE10 to Target
Board
Jumper Settings
Connecting
Power
Summary
The ICE10 connects to any PC through a standard RS-232 port (COM port). Connect
the RS-232 Cable between the ICE10 and any free COM port on the PC. AVR Studio
will automatically search through all available COM ports and detect the emulator.
Note:
If there are other devices taking control over the COM ports, these have to be
shut down before starting AVR Studio. AVR Studio cannot force control over a
COM port if other resources have control of the port (e.g., Modem, IrDA, PDA,
etc.)
Depending on which AVR microcontroller should be emulated, either the ATtiny15POD
1 shows which Pod to use.
Table 2-1. Pod Selection
POD
Supported AVR Microcontrollers
ATtiny15POD
ATtiny15
AT90ADCPOD
ATtiny11, ATtiny12, ATtiny22, ATtiny28 AT90S1200, AT90S2313,
AT90S/LS2323, AT90S/LS2343, AT90S/LS2333, AT90S/LS4433,
AT90S4414, AT90S8515, AT90S/LS4434, AT90S/LS8535
In short, the ATtiny15POD should be used for ATtiny15 only. The AT90ADCPOD is
used for all other listed devices.
The configuration system on the ATtiny15POD and AT90ADCPOD is different. The
AT90ADCPOD uses jumpers that need to be placed manually on the Pod. The
ATtiny15POD uses a jumperless system where all configuration is done directly from
AVR Studio. For in-depth information about AT90ADCPOD jumper settings see Section
The ICE10 system has an internal power regulator that delivers 15W at 5V. The ICE10
itself uses about 10W. The power supply delivered with the ICE10 is dimensioned to
meet the requirements of the emulator. If another power supply is used, it should supply
a voltage between 9 and 15 VDC and a minimum of 20W. The battery eliminator con-
nector on the ICE10 system is a standard type with 2.1 mm center tap. Ground should
be connected to the center tap.
Note:
The target application power must not be present when the emulator is turned
off, as this may cause damage to the pod.
Complete the following procedure in order to start using the ICE10. Before connecting
the probe cable to the user application:
Connect the RS-232 cable between the ICE10 unit and the PC serial port.
Connect the correct pod card to the ICE10 unit with the supplied pod cable.
Connect the correct probe cable to the pod.
Make sure that the pod settings (jumpers) on AT90ADCPOD are set according to the
requirements.
Connect the enclosed power supply (9 - 15 VDC) to the ICE10 unit.
Turn on the power and check that the red LED marked POWER is lit.
After a short time (<10 s), the green LED marked READY will be lit and the ICE10
system will be ready.
AVR ? ATICE10 User Guide
2-3
相关PDF资料 |
PDF描述 |
|---|---|
| ATICE50POD | REPLACEMENT POD FOR ICE40,ICE50 |
| ATQT600IB | BOARD INTERFACE ATQT600IB |
| ATSTK1000 | KIT STARTER FOR AVR32AP7000 |
| ATSTK501 | ADAPTER KIT FOR 64PIN AVR MCU |
| ATSTK502 | MOD EXPANSION AVR STARTER 500 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATICE10UPGR | 功能描述:KIT UPGRADE ICEPRO TO ICE10 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
| ATICE200 | 制造商:Atmel Corporation 功能描述: |
| ATICE200- | 制造商:Atmel Corporation 功能描述:LOW COST ICE FOR AVR FAMILY |
| ATICE30 | 制造商:Atmel Corporation 功能描述: |
| ATICE40 | 功能描述:EMULATOR IN-CIRCUIT TINY26/MEGA8 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
发布紧急采购，3分钟左右您将得到回复。