参数资料
| 型号： | ATICE10 |
| 厂商： | Atmel |
| 文件页数： | 18/35页 |
| 文件大小： | 0K |
| 描述： | AVR IN CIRCUIT EMULATOR |
| 标准包装： | 1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页当前第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
Using the ICE10
Table 3-1. Pinout for Aux Connector
Signal
Aux
Signal
GND
Input 0
Input 1
Input 2
Input 3
Input 4
GND
Pin 1
Pin 3
Pin 5
Pin 7
Pin 9
Pin 11
Pin 13
Pin 2
Pin 4
Pin 6
Pin 8
Pin 10
Pin 12
Pin 14
GND
Output 0
Output 1
Output 2
Output 3
Output 4
GND
There are three global mask registers that are used to control the behavior of the
triggers:
The Trigger Output Global Mask Register controls which of the output pins are
allowed to be controlled by the trigger settings in the code. An output pin that is
disabled will remain low even if a trigger point for that particular pin is set in the code.
The Trigger Input Global Mask Register controls which of the input pins are allowed to
break the emulator. If more than one line is enabled, the emulator will break on either
one, but will not store any information about which input caused the event. Note that
unconnected inputs are pulled high by internal pull-up resistors. Unused lines must
not be enabled.
The External Trace Mask Register controls which of the input pins will be stored in the
trace memory. Input pins that are not enabled in this register will be stored as zero in
the trace memory. To be traced, input signals must be valid and stable at the rising
edge of the AVR clock and for 50 ns thereafter. It is also necessary that the trace
buffer is enabled.
The trigger input and the external trace are two independent functions acting on the
same input pins. Note that the trigger logic is asynchronous and edge driven, whereas
the trace logic is clocked on the AVR clock. The emulator may therefore break on a
glitch signal that is too narrow to be traced.
The details on how to enable and set up triggers and mask registers are presented in
“AVR Studio On-line Help”.
3-4
AVR ? ATICE10 User Guide
相关PDF资料 |
PDF描述 |
|---|---|
| ATICE50POD | REPLACEMENT POD FOR ICE40,ICE50 |
| ATQT600IB | BOARD INTERFACE ATQT600IB |
| ATSTK1000 | KIT STARTER FOR AVR32AP7000 |
| ATSTK501 | ADAPTER KIT FOR 64PIN AVR MCU |
| ATSTK502 | MOD EXPANSION AVR STARTER 500 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATICE10UPGR | 功能描述:KIT UPGRADE ICEPRO TO ICE10 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
| ATICE200 | 制造商:Atmel Corporation 功能描述: |
| ATICE200- | 制造商:Atmel Corporation 功能描述:LOW COST ICE FOR AVR FAMILY |
| ATICE30 | 制造商:Atmel Corporation 功能描述: |
| ATICE40 | 功能描述:EMULATOR IN-CIRCUIT TINY26/MEGA8 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
发布紧急采购，3分钟左右您将得到回复。