参数资料
| 型号： | ATICE10 |
| 厂商： | Atmel |
| 文件页数： | 24/35页 |
| 文件大小： | 0K |
| 描述： | AVR IN CIRCUIT EMULATOR |
| 标准包装： | 1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页
AT90ADCPOD Configuration
Table 4-3. Settings of PW2, PW1 and PW0
Targe V CC
2.7 - 2.9V
3.0 - 3.3V
3.4 - 3.7V
3.8 - 4.1V
4.2 - 4.5V
4.6 - 4.8V
4.9 - 5.1V
5.2 - 5.5V
PW2
(ON)
(ON)
(ON)
(ON)
(OFF)
(OFF)
(OFF)
(OFF)
PW1
(ON)
(ON)
(OFF)
(OFF)
(ON)
(ON)
(OFF)
(OFF)
PW0
(ON)
(OFF)
(ON)
(OFF)
(ON)
(OFF)
(ON)
(OFF)
4.4
4-4
The ICE10 Clock
System
The AVR ICE10 system can use one of three available clock sources:
Internal programmable clock in the ICE10
Crystal from the user application
External oscillator from the user application
The internal clock can be adjusted between 400 kHz and 20 MHz. Any frequency within
this range can be selected, and will be produced with an accuracy better than 200 PPM
for most frequencies.
If an external clock source from the user application is used this can be in the range of
32.768 kHz to 10 MHz. To use an external clock source, select External Oscillator in the
Emulator Options menu in AVR Studio. It is important to tune the oscillator driver by
choosing the corresponding range in the Clock Range menu to make the clock system
work properly with an external crystal.
On the pod card, the XTAL pins are connected to the ICE10 by using the 2-wire cable.
Connect the cable from J103 to the 2-pin header nearest the used probe connector.
Table 4-4. Connections of 2-wire Cable
Device
2-wire Cable
S1200 and S2313
Connect J103 and J305
S4414 and S8515
Connect J103 and J306
ATtiny11, ATtiny12, ATtiny22, S2323, and S2343
Connect J103 and J307
S4434 and S8535
Connect J103 and J308
ATtiny28, S4433, and S2333
Connect J103 and J309
Pin 1 on each connector is labeled with *.
Connector J101 must be left open if the clock source from the user application is a crys-
tal, If the clock source from the user application is an oscillator, a jumper must be
mounted on connector J101. Table 4-5 shows the settings for J101. The switch S101
must be in position OFF in both cases.
AVR ? ATICE10 User Guide
相关PDF资料 |
PDF描述 |
|---|---|
| ATICE50POD | REPLACEMENT POD FOR ICE40,ICE50 |
| ATQT600IB | BOARD INTERFACE ATQT600IB |
| ATSTK1000 | KIT STARTER FOR AVR32AP7000 |
| ATSTK501 | ADAPTER KIT FOR 64PIN AVR MCU |
| ATSTK502 | MOD EXPANSION AVR STARTER 500 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| ATICE10UPGR | 功能描述:KIT UPGRADE ICEPRO TO ICE10 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
| ATICE200 | 制造商:Atmel Corporation 功能描述: |
| ATICE200- | 制造商:Atmel Corporation 功能描述:LOW COST ICE FOR AVR FAMILY |
| ATICE30 | 制造商:Atmel Corporation 功能描述: |
| ATICE40 | 功能描述:EMULATOR IN-CIRCUIT TINY26/MEGA8 RoHS:否 类别:编程器，开发系统 >> 过时/停产零件编号 系列:- 标准包装:1 系列:- 类型:MCU 适用于相关产品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、缆线、软件、数据表和用户手册 其它名称:520-1035 |
发布紧急采购，3分钟左右您将得到回复。