收藏本站
参数资料
型号： ATTINY43U-MUR
厂商： Atmel
文件页数： 62/158页
文件大小： 0K
描述： MCU AVR 4KB FLASH 8MHZ 20QFN
产品培训模块： tinyAVR Introduction
标准包装： 6,000
系列： AVR® ATtiny
核心处理器： AVR
芯体尺寸： 8-位
速度： 8MHz
连通性： USI
外围设备： 欠压检测/复位，POR，PWM，温度传感器，WDT
输入/输出数： 16
程序存储器容量： 4KB（2K x 16）
程序存储器类型： 闪存
EEPROM 大小： 64 x 8
RAM 容量： 256 x 8
电压 - 电源 (Vcc/Vdd)： 1.8 V ~ 5.5 V
数据转换器： A/D 4x10b
振荡器型： 内部
工作温度： -40°C ~ 85°C
封装/外壳： 20-WFQFN 裸露焊盘
包装： 带卷 (TR)
154
8048C–AVR–02/12
ATtiny43U
When programming the EEPROM, an auto-erase cycle is built into the self-timed programming
operation (in the Serial mode ONLY) and there is no need to first execute the Chip Erase
instruction. The Chip Erase operation turns the content of every memory location in both the
Program and EEPROM arrays into 0xFF.
Depending on CKSEL Fuses, a valid clock must be present. The minimum low and high periods
for the serial clock (SCK) input are defined as follows:
Low:> 2 CPU clock cycles for f
ck < 12 MHz, 3 CPU clock cycles for fck >= 12 MHz
High:> 2 CPU clock cycles for f
ck < 12 MHz, 3 CPU clock cycles for fck >= 12 MHz
19.7.1
Serial Programming Algorithm
When writing serial data to the ATtiny43U, data is clocked on the rising edge of SCK.
When reading data from the ATtiny43U, data is clocked on the falling edge of SCK. See Figure
20-8 and Figure 20-9 for timing details.
To program and verify the ATtiny43U in the Serial Programming mode, the following sequence
is recommended (see four byte instruction formats in Table 19-16):
1.
Power-up sequence:
Apply power between V
CC and GND while RESET and SCK are set to “0”. In some sys-
tems, the programmer can not guarantee that SCK is held low during power-up. In this
case, RESET must be given a positive pulse of at least two CPU clock cycles duration
after SCK has been set to “0”. The duration of the pulse must be at least t
RST plus two
CPU clock cycles. See Table 20-4 on page 161 for definition of minimum pulse width
on RESET pin, t
RST
2.
Wait for at least 20 ms and enable serial programming by sending the Programming
Enable serial instruction to pin MOSI.
3.
The serial programming instructions will not work if the communication is out of syn-
chronization. When in sync. the second byte (0x53), will echo back when issuing the
third byte of the Programming Enable instruction. Whether the echo is correct or not, all
four bytes of the instruction must be transmitted. If the 0x53 did not echo back, give
RESET a positive pulse and issue a new Programming Enable command.
4.
The Flash is programmed one page at a time. The memory page is loaded one byte at
a time by supplying the 5 LSB of the address and data together with the Load Program
memory Page instruction. To ensure correct loading of the page, the data low byte must
be loaded before data high byte is applied for a given address. The Program memory
Page is stored by loading the Write Program memory Page instruction with the 3 MSB
of the address. If polling (RDY/BSY) is not used, the user must wait at least t
WD_FLASH
before issuing the next page. (See Table 19-15 on page 155.) Accessing the serial pro-
gramming interface before the Flash write operation completes can result in incorrect
programming.
5.
A: The EEPROM array is programmed one byte at a time by supplying the address and
data together with the appropriate Write instruction. An EEPROM memory location is
first automatically erased before new data is written. If polling (RDY/BSY) is not used,
the user must wait at least t
WD_EEPROM before issuing the next byte. (See Table 19-15
on page 155.) In a chip erased device, no 0xFFs in the data file(s) need to be pro-
grammed.
B: The EEPROM array is programmed one page at a time. The Memory page is loaded
one byte at a time by supplying the 2 LSB of the address and data together with the
Load EEPROM Memory Page instruction. The EEPROM Memory Page is stored by
相关PDF资料
PDF描述
VI-J14-IW CONVERTER MOD DC/DC 48V 100W
VE-B2T-IW-F4 CONVERTER MOD DC/DC 6.5V 100W
ATTINY84-20SSUR MCU AVR 8KB FLASH 10MHZ 14SOIC
ADG1206YRUZ-REEL7 IC MULTIPLEXER 16X1 28TSSOP
VI-BWX-IX CONVERTER MOD DC/DC 5.2V 75W
相关代理商/技术参数
参数描述
ATTINY43U-SU 功能描述:8位微控制器 -MCU AVR 4KB, 64B EE 8MHz 256B SRAM, 0.9V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATTINY43U-SUR 功能描述:8位微控制器 -MCU 4KB FLSH 64B EE 256B SRAM-8MHz, IND 0.9V RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATTINY44 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
ATTINY44-15MZ 功能描述:8位微控制器 -MCU 4KB Flash 15MHz Auto 125-degrees C RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
ATTINY44-15SSZ 功能描述:8位微控制器 -MCU 4KB Flash 15MHz Auto 125-degrees C RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*