- 您现在的位置：买卖IC网 > Datasheet目录316 > BU9844GUL-WE2 (Rohm Semiconductor)IC EEPROM 16KBIT 2WIRE VCSP50L1 Datasheet资料下载
参数资料
| 型号： | BU9844GUL-WE2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 16/29页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 16KBIT 2WIRE VCSP50L1 |
| 标准包装： | 3,000 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 16K (2K x 8) |
| 速度： | 400kHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 1.7 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 6-UFBGA，CSPBGA |
| 供应商设备封装： | VCSP50L1 |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页
BU9844GUL-W (16Kbit)
Datasheet
Software reset
Software reset is executed when to avoid malfunction after power on, and to reset during command input. Software reset
has several kinds, and 3 kinds of them are shown in the figure below. (Refer to Figure 40-(a), Figure 40-(b) and Figure
40-(c).) In dummy clock input area, release the SDA bus (“H” by pull up). In dummy clock area, ACK output and read data
“0” (both “L” level) may be output from EEPROM, therefore, if “H” is input forcibly, output may conflict and over current may
flow, leading to instantaneous power failure of system power source or influence upon devices.
Dummy clock x14
Start x2
SCL
1
2
13
14
Normal command
SDA
Normal command
Figure 40-(a) The case of dummy clock + START + START + command input
Start
Dummy clock x9
Start
SCL
1
2
8
9
Normal command
SDA
Normal command
Figure 40-(b) The case of START + 9 dummy clocks + START + command input
Start x 9
SCL
1
2
3
7
8
9
Normal command
SDA
Normal command
Figure 40-(c) START x 9 + command input
* Start normal command from START input.
Acknowledge polling
During internal write execution, all input commands are ignored, therefore ACK is not sent back. During internal automatic
write execution after write cycle input, next command (slave address) is sent, and if the first ACK signal sends back “L”,
then it means end of write action, while if it sends back “H”, it means now in writing. By use of acknowledge polling, next
command can be executed without waiting for tWR=5ms.
When to write continuously, R / W = 0, when to carry out current read cycle after write, slave address R / W = 1 is sent,
and if ACK signal sends back “L”, then execute word address input and data output and so forth.
During internal write,
First write command
ACK = HIGH is sent back.
S
T
A
R
T
Write command
S
T
O
P
S
T
A
R
T
Slave A
C
address K
H
S
T
A
R
T
Slave
address
A
C
K
H
…
tWR
Second write command
…
S
T
A
R
T
Slave A
C
address K
H
S
T
A
R
T
Slave
address
A
C
K
L
Word
address
A
C
K
L
Data
A
C
K
L
S
T
O
P
tWR
After completion of internal write,
ACK = LOW is sent back, so input
next word address and data in
succession.
Figure 41. Case to continuously write by acknowledge polling
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
16/26
TSZ02201-0R2R0G100470-1-2
17.Sep.2013 Rev.002
相关PDF资料 |
PDF描述 |
|---|---|
| BU9847GUL-WE2 | IC EEPROM 4KBIT 2WIRE VCSP50L1 |
| BU9880GUL-WE2 | IC EEPROM 64KBIT 2WIRE VCSP50L1 |
| BU9882FV-WE2 | IC EEPROM 2KBIT 400KHZ 14SSOP |
| BU9883FV-WE2 | IC EEPROM 6KBIT 400KHZ SSOP16 |
| BU9889GUL-WE2 | IC EEPROM 8KBIT 2WIRE VCSP50L1 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BU9847GUL-W | 制造商:ROHM 制造商全称:Rohm 功能描述:WL-CSP EEPROM family I2C BUS |
| BU9847GUL-W_10 | 制造商:ROHM 制造商全称:Rohm 功能描述:WL-CSP EEPROM family I2C BUS |
| BU9847GUL-WE2 | 功能描述:电可擦除可编程只读存储器 电可擦除可编程只读存储器 Serial-2Wire 4Kb RoHS:否 制造商:Atmel 存储容量:2 Kbit 组织:256 B x 8 数据保留:100 yr 最大时钟频率:1000 KHz 最大工作电流:6 uA 工作电源电压:1.7 V to 5.5 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 |
| BU98570CH-3BW | 制造商:ROHM 制造商全称:Rohm 功能描述:65,536 Colors 98RGB x 70 STN LCD control driver |
| BU98582CH-3BW | 制造商:ROHM 制造商全称:Rohm 功能描述:65,536 Colors 104RGB x 82 STN LCD control driver |
发布紧急采购，3分钟左右您将得到回复。