- 您现在的位置：买卖IC网 > Datasheet目录316 > BU99901GUZ-WE2 (Rohm Semiconductor)IC EEPROM 32KBIT 2WIRE VCSP Datasheet资料下载
参数资料
| 型号： | BU99901GUZ-WE2 |
| 厂商： | Rohm Semiconductor |
| 文件页数： | 13/26页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 32KBIT 2WIRE VCSP |
| 标准包装： | 3,000 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 32K (4K x 8) |
| 速度： | 400kHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 1.7 V ~ 3.6 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 6-XFBGA，CSPBGA |
| 供应商设备封装： | VCSP30L1 |
| 包装： | 带卷 (TR) |
BU99901GUZ-W (32Kbit)
Datasheet
I C BUS data communication
I C BUS data communication starts by start condition input, and ends by stop condition input. Data is always 8bit long,
● I 2 C BUS communication
2
2
and acknowledge is always required after each byte.
I 2 C BUS carries out data transmission with plural devices connected by 2 communication lines of serial data (SDA) and
serial clock (SCL).
Among devices, there are “master” that generates clock and control communication start and end, and “slave” that is
controlled by addresses peculiar to devices.
EEPROM becomes “slave”. And the device that outputs data to bus during data communication is called “transmitter”,
and the device that receives data is called “receiver”.
SDA
SCL
1-7
8
9
1-7
8
9
1-7
8
9
S
P
START
ADDRESS
R/W
ACK
DATA
ACK
DATA
ACK
STOP
condition
condition
Figure 32. Data transfer timing
○ Start condition (start bit recognition)
? Before executing each command, start condition (start bit) where SDA goes from 'HIGH' down to 'LOW' when SCL
is 'HIGH' is necessary.
? This IC always detects whether SDA and SCL are in start condition (start bit) or not, therefore, unless this condition is
satisfied, any command is executed.
○ Stop condition (stop bit recognition)
? Each command can be ended by SDA rising from 'LOW' to 'HIGH' when stop condition (stop bit), namely, SCL is 'HIGH'
○ Acknowledge (ACK) signal
? This acknowledge (ACK) signal is a software rule to show whether data transfer has been made normally or not. In
master and slave, the device (μ-COM at slave address input of write command, read command, and this IC at data
output of read command) at the transmitter (sending) side releases the bus after output of 8bit data.
? The device (this IC at slave address input of write command, read command, and μ-COM at data output of read
command) at the receiver (receiving) side sets SDA 'LOW' during 9 clock cycles, and outputs acknowledge signal (ACK
signal) showing that it has received the 8bit data.
? This IC, after recognizing start condition and slave address (8bit), outputs acknowledge signal (ACK signal) 'LOW'.
? Each write action outputs acknowledge signal) (ACK signal) 'LOW', at receiving 8bit data (word address and write data).
? Each read action outputs 8bit data (read data), and detects acknowledge signal (ACK signal) 'LOW'.
? When acknowledge signal (ACK signal) is detected, and stop condition is not sent from the master (μ-COM) side, this
IC continues data output. When acknowledge signal (ACK signal) is not detected, this IC stops data transfer, and
recognizes stop condition (stop bit), and ends read action. And this IC gets in standby status.
○ Device addressing
? Output slave address after start condition from master.
? The significant 4 bits of slave address are used for recognizing a device type.
The device code of this IC is fixed to '1010'.
? The most insignificant bit ( エラー ! 編集中のフィールド コードからは、オブジェクトを作成できません。 --- エラー ! 編
集中のフィールド コードからは、オブジェクトを作成できません。 ) of slave address is used for designating write or
read action, and is as shown below.
Setting エラー ! 編集中のフィールド コードからは、オブジェクトを作成できません。 to 0 --- write (setting 0 to word
address setting of random read)
Setting エラー ! 編集中のフィールド コードからは、オブジェクトを作成できません。 to 1 --- read
Type
BU99901GUZ-W
Slave address
1 1 1 0 0 0 0 エラー ! 編
集中のフィールド コードからは、オブジェクトを作成できません。
www.rohm.com
? 2012 ROHM Co., Ltd. All rights reserved.
TSZ22111 ? 15 ? 001
13/23
TSZ02201-0R2R0G100280-1-2
4.SEP.2012 Rev.001
相关PDF资料 |
PDF描述 |
|---|---|
| BUK218-50DY,118 | TOPFET DUAL SWITCH D2PAK |
| BVL121200003N | BATTERY CHG UNIV 12VDC @ 1.2A |
| BVW241250003A | BATTERY CHG UNIV 24VDC @ 1.25A |
| C-14245 | RACKMOUNT INTERNAL CHASSIS |
| C-1555 | CABINET SLOPING PANEL PRESTIGE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| BU9H-103R25BL | 制造商:Coilcraft Inc 功能描述:Common mode choke, power line, RoHS |
| BU9H-1320R7BL | 制造商:Coilcraft Inc 功能描述:Common mode choke, power line, RoHS |
| BU9H-2011R6BL | 制造商:Coilcraft Inc 功能描述:Common mode choke, power line, RoHS |
| BU9H-2820R5BL | 制造商:Coilcraft Inc 功能描述:Common mode choke, power line, RoHS |
| BU9H-6011R0BL | 制造商:Coilcraft Inc 功能描述:Common mode choke, power line, RoHS |
发布紧急采购，3分钟左右您将得到回复。