收藏本站
参数资料
型号： C8051F000-TB
厂商： Silicon Laboratories Inc
文件页数： 43/171页
文件大小： 0K
描述： BOARD PROTOTYPING W/C8051F000
标准包装： 1
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
Figure 18.9. SCON: Serial Port Control Register
R/W
Reset Value
SM0
SM1
SM2
REN
TB8
RB8
TI
RI
00000000
Bit7
Bit6
Bit5
Bit4
Bit3
Bit2
Bit1
Bit0
SFR Address:
(bit addressable)
0x98
Bits7-6: SM0-SM1: Serial Port Operation Mode.
These bits select the Serial Port Operation Mode.
SM0
SM1
Mode
0
Mode 0: Synchronous Mode
0
1
Mode 1: 8-Bit UART, Variable Baud Rate
1
0
Mode 2: 9-Bit UART, Fixed Baud Rate
1
Mode 3: 9-Bit UART, Variable Baud Rate
Bit5:
SM2: Multiprocessor Communication Enable.
The function of this bit is dependent on the Serial Port Operation Mode.
Mode 0: No effect
Mode 1: Checks for valid stop bit.
0: Logic level of stop bit is ignored.
1: RI will only be activated if stop bit is logic level 1.
Mode 2 and 3: Multiprocessor Communications Enable.
0: Logic level of ninth bit is ignored.
1: RI is set and an interrupt is generated only when the ninth bit is logic 1.
Bit4:
REN: Receive Enable.
This bit enables/disables the UART receiver.
0: UART reception disabled.
1: UART reception enabled.
Bit3:
TB8: Ninth Transmission Bit.
The logic level of this bit will be assigned to the ninth transmission bit in Modes 2 and 3. It
is not used in Modes 0 and 1. Set or cleared by software as required.
Bit2:
RB8: Ninth Receive Bit.
The bit is assigned the logic level of the ninth bit received in Modes 2 and 3. In Mode 1, if
SM2 is logic 0, RB8 is assigned the logic level of the received stop bit. RB8 is not used in
Mode 0.
Bit1:
TI: Transmit Interrupt Flag.
Set by hardware when a byte of data has been transmitted by the UART (after the 8
th bit in
Mode 0, or at the beginning of the stop bit in other modes). When the UART interrupt is
enabled, setting this bit causes the CPU to vector to the UART interrupt service routine.
This bit must be cleared manually by software
Bit0:
RI: Receive Interrupt Flag.
Set by hardware when a byte of data has been received by the UART (after the 8
th bit in
Mode 0, or after the stop bit in other modes – see SM2 bit for exception). When the
UART interrupt is enabled, setting this bit causes the CPU to vector to the UART interrupt
service routine. This bit must be cleared manually by software.
137
Rev. 1.7
相关PDF资料
PDF描述
RP15-4812DF/N-HC CONV DC/DC 15W 36-75VIN +/-12V
MAX6439UTAHTD3+T IC BATTERY MON SNGL SOT23-6
C8051F124-TB BOARD PROTOTYPING W/C8051F124
SDR1105-560KL INDUCTOR 56UH 2A SMD
GBM22DREH CONN EDGECARD 44POS .156 EYELET
相关代理商/技术参数
参数描述
C8051F001 功能描述:8位微控制器 -MCU 32KB 12ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F001-GQ 功能描述:8位微控制器 -MCU 32KB 12ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F001-GQR 功能描述:8位微控制器 -MCU 32KB 12ADC 48Pin MCU Tape and Reel RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F001R 功能描述:8位微控制器 -MCU C 12Bit 48Pin RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
C8051F002 功能描述:8位微控制器 -MCU 32KB 12ADC RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*