- 您现在的位置：买卖IC网 > PDF目录3798 > C8051F236-GQ (Silicon Laboratories Inc)IC 8051 MCU 8K FLASH 48TQFP PDF资料下载
参数资料
| 型号： | C8051F236-GQ |
| 厂商： | Silicon Laboratories Inc |
| 文件页数： | 129/146页 |
| 文件大小： | 0K |
| 描述： | IC 8051 MCU 8K FLASH 48TQFP |
| 产品培训模块： | Serial Communication Overview |
| 标准包装： | 250 |
| 系列： | C8051F2xx |
| 核心处理器： | 8051 |
| 芯体尺寸： | 8-位 |
| 速度： | 25MHz |
| 连通性： | SPI，UART/USART |
| 外围设备： | 欠压检测/复位，POR，WDT |
| 输入/输出数： | 32 |
| 程序存储器容量： | 8KB（8K x 8） |
| 程序存储器类型： | 闪存 |
| RAM 容量： | 1.25K x 8 |
| 电压 - 电源 (Vcc/Vdd)： | 2.7 V ~ 3.6 V |
| 振荡器型： | 内部 |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 48-TQFP |
| 包装： | 托盘 |
| 产品目录页面： | 623 (CN2011-ZH PDF) |
| 其它名称： | 336-1244 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页当前第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页
C8051F2xx
Rev. 1.6
83
9.5.
Power Management Modes
The CIP-51 core has two software programmable power management modes: Idle and Stop. Idle mode
halts the CPU while leaving the external peripherals and internal clocks active. In Stop mode, the CPU is
halted, all interrupts and timers (except the Missing Clock Detector) are inactive, and the system clock is
stopped. Since clocks are running in Idle mode, power consumption is dependent upon the system clock
frequency and the number of peripherals left in active mode before entering Idle. Stop mode consumes
the least power. SFR Definition 9.14 describes the Power Control Register (PCON) used to control the
CIP-51’s power management modes.
Although the CIP-51 has Idle and Stop modes built in (as with any standard 8051 architecture), power
management of the entire MCU is better accomplished by enabling/disabling individual peripherals as
needed. Each analog peripheral can be disabled when not in use and put into low power mode. Turning
off the active oscillator saves even more power, but requires a reset to restart the MCU.
9.5.1. Idle Mode
Setting the Idle Mode Select bit (PCON.0) causes the CIP-51 to halt the CPU and enter Idle mode as soon
as the instruction that sets the bit completes.
All internal registers and memory maintain their original
data. All analog and digital peripherals can remain active during Idle mode.
Idle mode is terminated when an enabled interrupt or RST is asserted. The assertion of an enabled inter-
rupt will cause the Idle Mode Selection bit (PCON.0) to be cleared and the CPU will resume operation.
The pending interrupt will be serviced and the next instruction to be executed after the return from interrupt
(RETI) will be the instruction immediately following the one that set the Idle Mode Select bit. If Idle mode is
terminated by an internal or external reset, the CIP-51 performs a normal reset sequence and begins pro-
gram execution at address 0x0000.
Note: If the instruction following the write of the IDLE bit is a single-byte instruction and an interrupt occurs
during the execution phase of the instruction that sets the IDLE bit, the CPU may not wake from Idle mode
when a future interrupt occurs. Any instructions that set the IDLE bit should be followed by an instruction
that has 2 or more op-code bytes, for example:
// in ‘C’:
PCON |= 0x01;
// set IDLE bit
PCON = PCON;
// ... followed by a 3-cycle dummy instruction
; in assembly:
ORL PCON, #01h
; set IDLE bit
MOV PCON, PCON
; ... followed by a 3-cycle dummy instruction
If enabled, the WDT will eventually cause an internal watchdog reset and thereby terminate the Idle mode.
This feature protects the system from an unintended permanent shutdown in the event of an inadvertent
write to the PCON register. If this behavior is not desired, the WDT may be disabled by software prior to
entering the Idle mode if the WDT was initially configured to allow this operation. This provides the oppor-
tunity for additional power savings, allowing the system to remain in the Idle mode indefinitely, waiting for
an external stimulus to wake up the system. Refer to Section 12.7 Watchdog Timer for more information
on the use and configuration of the WDT.
9.5.2. Stop Mode
Setting the Stop Mode Select bit (PCON.1) causes the CIP-51 to enter Stop mode as soon as the instruc-
tion that sets the bit completes. In Stop mode, the CPU and oscillators are stopped, effectively shutting
相关PDF资料 |
PDF描述 |
|---|---|
| USB-B-S-F-B-SM-R-TR | USB TYPE B 2.0 BLACK SMD |
| USB-A-S-F-W-SM2-R-TR | USB TYPE A WHITE SNGL SMD |
| USB-B-S-F-W-TH | USB TYPE B 2.0 WHITE T/H |
| P87C52X2BN,112 | IC 80C51 MCU 8K OTP 40-DIP |
| USB-B-S-F-B-TH-R | USB TYPE B 2.0 BLACK T/H |
相关代理商/技术参数 |
参数描述 |
|---|---|
| C8051F236-GQR | 功能描述:8位微控制器 -MCU 8KB 1KRam 48Pin MCU Tape and Reel RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| C8051F236R | 功能描述:8位微控制器 -MCU T-01280 Ram 48Pin RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| C8051F2XX | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Mixed Signal 8 kB ISP Flash MCU Family |
| C8051F300 | 功能描述:8位微控制器 -MCU 8KB 8ADC 2%osc RoHS:否 制造商:Silicon Labs 核心:8051 处理器系列:C8051F39x 数据总线宽度:8 bit 最大时钟频率:50 MHz 程序存储器大小:16 KB 数据 RAM 大小:1 KB 片上 ADC:Yes 工作电源电压:1.8 V to 3.6 V 工作温度范围:- 40 C to + 105 C 封装 / 箱体:QFN-20 安装风格:SMD/SMT |
| C8051F300DK | 功能描述:开发板和工具包 - 8051 MCU DEVELOPMENT KIT W/ US POWER SUPPLY RoHS:否 制造商:Silicon Labs 产品:Development Kits 工具用于评估:C8051F960, Si7005 核心: 接口类型:USB 工作电源电压: |
发布紧急采购，3分钟左右您将得到回复。